The 50 most-cited articles in Macromolecules, 2018

We demonstrate a facile and universal strategy in the fabrication of dual-cross-linked (DC) single network hydrogels with high toughness, “nonswellability”, rapid self-healing, and versatile adhesiveness based on polymer–tannic acid (TA) multiple hydrogen bonds. Two widely used hydrogels, physically cross-linked poly(vinyl alcohol) and chemically cross-linked polyacrylamide, have been transformed to TA-based DC hydrogels by dipping the corresponding aerogels into TA solution. The second cross-link via multiple polymer–TA hydrogen bonds effectively suppresses the crack propagation, resulting in both DC gels with high mechanical strength. But these two TA-based DC hydrogels go through different deformation mechanisms during the stretching based on analyzing their stress–strain curves using the Mooney–Rivlin equation. Moreover, these DC hydrogels are swelling-resistant, with strong toughness, good self-recoverability, rapid self-healing, and versatile adhesiveness. This work provides a simple route to fabricate multifunctional DC hydrogels, hopefully promoting their applications as…

A method for preparing reprocessable epoxy thermoset is presented. The process is composed of synthesis of a bisphenol monomer bridged by an imine bond, glycidylation of the bisphenol, and cross-linking with a hardener to form thermoset. The resulting epoxy thermoset possesses comparable properties to conventional high-performance thermosets made from bisphenol A. However, when treated by a stimulus like acid, temperature, and/or water, the described thermoset exhibits reprocessability. Degradation and recycling involve hydrolysis and re-formation of imine bonds; reshaping and repairing of the thermoset are realized through imine exchange reactions. All the described processes require no metal catalyst, press heating, or additional monomer, which significantly widens thermoset reprocessing.

Vitrimers form a promising class of dynamic polymer networks, but they have an Achilles’ heel: elastomeric vitrimers exhibit significant creep under conditions where permanently cross-linked, elastomeric networks exhibit little or no creep. We demonstrate that vitrimers can be designed with strongly suppressed creep and excellent reprocessability by incorporating a substantial yet subcritical fraction of permanent cross-links. This critical fraction of permanent cross-links, which has little or no detrimental effect on reprocessability, is defined by the gelation point of only permanent cross-links leading to a percolated permanent network. Via a modification of classic Flory–Stockmayer theory, we have developed a simple theory that quantitatively predicts an approximate limiting fraction. To test our theory, we designed vitrimers with controlled fractions of permanent cross-links based on thiol–epoxy click chemistry. We characterized the rubbery plateau modulus before and after reprocessing as well as stress relaxation of our original vitrimers. Our experimental results strongly…

Abstract Vitrimers are cross-linked polymer networks containing linkages that undergo thermally activated, associative exchange reactions, such that the cross-link density and overall network connectivity are preserved. Polycarbonates are industrially relevant polymers that, to our knowledge, have not yet been explored as vitrimers. We developed hydroxyl-functionalized polycarbonate networks that undergo transcarbonation exchange reactions at elevated temperatures in the presence of catalytic Ti(IV) alkoxides. The rate of transcarbonation within the networks, estimated through stress relaxation experiments, was tuned by adjusting the catalyst loading or hydroxyl group concentration in the networks. The polymer networks exhibit recovery of their tensile strength and plateau storage modulus (71–133%) after reprocessing. In addition to being reprocessable, the networks were hydrolyzed and decarboxylated in aqueous acid to recover 80 wt % of the precursor to the bifunctional cyclic carbonate monomer. These observations demonstrate that PC vitrimers are a novel class of strong,…

Conventional thermosets are built by nonrenewable fossil resources and are arduous to be reprocessed, recycled, and reshaped due to their permanent covalent cross-linking, and their flammability makes them unsafe during use. Here, for the first time, we synthesized a novel Schiff base precursor from abundant and renewable lignin derivative vanillin and produced malleable thermosets (Schiff base covalent adaptable networks (CANs)) combining high performance, super-rapid reprocessability, excellent monomer recovery, and arbitrary permanent shape changeability as well as outstanding fire resistance. The Schiff base CANs exhibited high glass transition temperatures of ∼178 °C, tensile strength of ∼69 MPa, tensile modulus of ∼1925 MPa, excellent flame retardancy with UL-94 V0 rating and V1 rating, and high LOI of ∼30%. Meanwhile, three Schiff base CANs showed high malleability with the activation energy of the bond exchange of 49–81 kJ mol –1 and could be reprocessed in 2–10 min at 180 °C. These Schiff base CANs provide a prime example to foster the development of advanced thermosetting…

Polyelectrolyte complexes are omnipresent both in nature and in the technological world, including nucleotide condensates, biological marine adhesives, food stabilizers, encapsulants, and carriers for gene therapy. However, the true phase behavior of complexes, resulting from associative phase separation of oppositely charged polyelectrolytes, remains poorly understood. Here, we rely on complementary experimental and simulation approaches to create a complete quantitative description of the phase behavior of polyelectrolyte complexes that represents a significant advance in our understanding of the underlying physics of polyelectrolyte complexation. Experiments employing multiple approaches with model polyelectrolytes—oppositely charged polypeptides poly( l -lysine) and poly( d, l -glutamic acid) of matched chain lengths—led to phase diagrams with compositions of the complex and the supernatant that were in excellent agreement with simulation results. Contrary to the widely accepted theory for complexation, we found preferential partitioning of salt ions into the supernatant phase.…

The design of high glass transition temperature ( T g ) thermoset materials with considerable reparability is a challenge. In this study, a novel biobased triepoxy (TEP) is synthesized and cured with an anhydride monomer in the presence of zinc catalyst. The cured TEP exhibits a high T g (187 °C) and comparable strength and modulus to the cured bisphenol A epoxy. By adopting the vitrimer chemistry, the cross-linked polymer materials are imparted significant stress relaxation and reparability via dynamic transesterification. It is noted that the reparability is closely related to the repairing temperature, external force, catalyst content, and the magnitude of rubbery modulus of the sample. The width of the crack from the cured TEP can be efficiently repaired within 10 min. This work introduces the first high- T g biobased epoxy material with excellent reparability and provides a valuable method for the design of high- T g self-healing materials suitable for high service temperature.

To date, all epoxy vitrimer systems reported in the literature rely on addition of significant amounts of catalysts to achieve the dynamic transesterification reaction (TER). However, the catalysts used in vitrimers are often toxic and have poor miscibility with organic compounds, and they may further comprise the application performance like corrosion resistance. Moreover, the reprocessing and recycling properties are highly dependent on the loading amount and the type of catalyst. In this study, two hyperbranched epoxy (HBE) prepolymers are synthesized and then reacted with succinic anhydride to prepare a catalyst-free epoxy vitrimer system. It is demonstrated that both the curing during the preparation of the cross-linked materials and the TER in the resulting cross-linked materials proceed properly without addition of external catalyst. We attributed this phenomenon to the abundant free hydroxyl groups in HBE which serve as both reacting moiety and catalyst in both curing and the TER processes. At elevated temperatures (>120 °C), the TER is activated to enable fast stress…

Hydrogels are usually recognized as soft and weak materials, the poor mechanical properties of which greatly limit their applications as structural elements. Designing of hydrogels with high strength and high modulus has both fundamental and practical significances. Herein we report a series of tough, stiff, and transparent hydrogels facilely prepared by copolymerization of 1-vinylimidazole and methacrylic acid in dimethyl sulfoxide followed by solvent exchange to water. The equilibrated hydrogels with water content of 50–60 wt % possessed excellent mechanical properties, with tensile breaking stress, breaking strain, Young’s modulus, and tearing fracture energy of 1.3–5.4 MPa, 40–330%, 20–170 MPa, and 600–4500 J/m 2, respectively. These tough hydrogels were also stable over a wide pH range (2 ≤ pH ≤ 10), resulting from the formation of dense and robust hydrogen bonds between imidazole and carboxylic acid groups. Moreover, the water content and mechanical properties of one gel can be adjusted over a wide range by controlling the dissociation and re-formation of hydrogen bonds during…

Abstract Over the past 10 years, the grafting of polymers from the surface of cellulose nanocrystals (CNCs) has gained substantial interest in both academia and industry due to the rapidly growing number of potential applications of surface-modified CNCs, which range from building blocks in nanocomposites and responsive nanomaterials to antimicrobial agents. CNCs are rod-like nanoparticles that can be isolated from renewable biosources and which exhibit high crystallinity, tunable aspect ratio, high stiffness, and strength. Upon drying, the abundance of surface hydroxyl groups often leads to a degree of irreversible aggregation, as a result of strong hydrogen bonding. Moreover, their relatively hydrophilic character renders CNCs incompatible with hydrophobic media, e.g., nonpolar solvents and polyolefin matrices. By grafting macromolecules from their surface, CNCs can be imparted with surface characteristics and other physicochemical properties that are reminiscent of the grafted polymer. This has allowed the design of nanoscale building blocks whose readily tunable properties are…

The self-healing abilities inside polymeric materials are desirable functions in materials science. Host–guest chemistry, combined with excellent properties of graphene, was used for the construction of multistimuli-responsive intrinsic self-healing epoxy materials. By ultraviolet (UV) curing, the unsaturated epoxy resin was connected with β-cyclodextrin/graphene complex through free radical copolymerization. The introduced complex, acting as macro-cross-linker and photothermal agent, can reconnect the damage-induced broken bonds through dynamic host–guest interaction. In this work, the epoxy composites exhibited a high healing efficiency of up to 79.2% and tensile strength of up to 20.8 MPa under heating or near-infrared stimulation, which represent relatively excellent values among all the reported intrinsic self-healing epoxy resin and host–guest self-healing systems.

Molecular dynamics simulations have been performed to study the effects of the cross-link density and distribution on the network topology, the dynamic structural properties, the tensile mechanical properties, and the viscoelastic properties of chemically cross-linked polymers. Simulation results show that the introduction of cross-links slows the chain dynamics down and thus leads to a slight increase in the glass transition temperature. Improving the cross-link dispersion state is found to be essentially equivalent to increasing the effective cross-link density, as reflected in the network topological features. The structural relaxation behavior is analyzed in terms of the incoherent intermediate dynamic structure factor, and the characteristic α-relaxation time is examined by the MCT and VFT equation. The results indicate that the time–temperature superposition principle holds on the segmental length scale but fails on the chain length scale, where it can be valid at sufficiently high temperature above the critical temperature. Furthermore, the mechanical property of polymer…

Vitrimers are covalently cross-linked polymeric materials that can be thermally processed in a liquid state without losing their network integrity. In this work, novel vitrimers based on the dynamic amine exchange reaction of vinylogous urea moieties are introduced. Following a systematic exploration of different vinylogous acyl compounds (urethanes, amides, and urea), vinylogous urea clearly emerges as showing the fastest intrinsic exchange kinetics. The combination of these networks with a simple acid catalyst (0.5 mol % pTsOH) resulted in materials with good mechanical properties ( T g ∼ 110 °C, E ∼ 2.2 GPa) and remarkably short relaxation times above T g, in the order of a few seconds when heated. This attractive combination of properties made it possible to prepare vinylogous urea based composites as enduring prepregs. We demonstrate that the dynamic material properties give fully cured composites that still allow an efficient thermal fusion of multiple layers as well as thermoforming. Finally, we also demonstrate fiber recycling by a simple chemical treatment.

Understanding the ionic diffusion mechanism in polymer electrolytes is critical to the development of advanced lithium-ion batteries. We report here molecular dynamics-based characterization of structures and diffusion in poly(ethylene oxide) (PEO) with lithium and bis(trifluoromethysulfonyl)imide (TFSI) ions imbedded into the PEO structure. We consider a range of temperatures (360–480 K), molecular weights (43, 22, 10, and 2 chains with 23, 45, 100, and 450 EO monomers, respectively), and ion concentrations ( r = 0.02, 0.04, 0.06, and 0.08 Li:EO) for which there is experimental data. The found dependence of the diffusion coefficients on these variables is in good agreement with experimental measurements. We then analyze how the diffusion performance depends on details of the atomistic diffusion mechanism, the motion of the Li and TFSI along the polymer chains and hopping between them, the role of polymer motion, the temperature dependence of the intrachain and interchain diffusion contributions to the total ionic diffusion coefficients, and how these depend on ionic concentration…

Anion exchange membrane fuel cells (AEMFCs) have attracted extensive attention in the recent years, primarily due to the distinct advantage potentials they have over the mainstream proton exchange membrane fuel cells. The anion exchange membrane (AEM) is the key component of AEMFC systems. Because of the unique characteristics of water management in AEMFCs, understanding the water mobility through AEMs is key for this technology, as it significantly affects (and limits) overall cell performances. This work presents a study of the equilibrium state and kinetics of water uptake (WU) for AEMs exposed to vapor source H 2 O. We investigate different AEMs that exhibit diverse water uptake behaviors. AEMs containing different backbones (fluorinated and hydrocarbon-based backbones) and different functional groups (various cations as part of the backbone or as pendant groups) were studied. Equilibrium WU isotherms are measured and fitted by the Park model. The influence of relative humidity and temperature is also studied for both equilibrium and dynamic WU. A characteristic time constant is…

Abstract A series of isotactic polypropylene (iPP) and polyethylene (PE) diblock, tetrablock, and hexablock copolymers (BCPs) were synthesized with tunable molecular weights using a hafnium pyridylamine catalyst. The BCPs were melt blended with 70 wt % high-density PE (HDPE) and 30 wt % iPP commercial homopolymers at concentrations between 0.2 and 5 wt %. The resulting blend morphologies were investigated using TEM, revealing uniformly dispersed iPP droplets ranging progressively in size with increasing BCP content from three-quarters to one-quarter of the diameter of the uncompatibilized mixture. Tensile tests revealed a dramatic enhancement in toughness based on the strain at break which increased from 10% for the unmodified blend to more than 300% with just 0.2 wt % BCP and over 500% with the addition of 0.5 wt % BCP or greater. Incorporation of BCPs in blends also improved the impact toughness, doubling the Izod impact strength to a level comparable to the neat HDPE with just 1 wt % additive. These improved blend properties are attributed to enhanced interfacial strength, which…

Abstract The increasing impact of atom transfer radical polymerization (ATRP) in fields beyond traditional polymer science has necessitated the development of alternative strategies for controlling polymer growth. Driven by applications that are sensitive to metal ion contamination, “greener” methodologies are emerging as a powerful alternative to conventional ATRP. Organic catalysis represents a major evolution of ATRP with metal-free systems holding significant potential as user-friendly methods for utility in biological and microelectronic applications. In addition, shifting from a combination of thermal activation/metal ions/ligands to simpler organic catalysis/light activation increases compatibility with functional monomers and allows the development of novel surface patterning strategies. Herein, we highlight key discoveries and recent developments in metal-free ATRP, while providing a perspective for future opportunities in this emerging area.

Vitrimers are a class of polymers that flow when heated but are insoluble. Vitrimers are made of covalent networks with dynamic links and/or cross-links that undergo an associative exchange reaction. These dynamic cross-links enable vitrimers to have interesting mechanical/rheological behavior, self-healing, adhesive, and shape memory properties. We demonstrate that vitrimers can self-assemble into complex meso- and nanostructures when cross-links and backbone monomers strongly interact. Vitrimers featuring polyethylene (PE) as the backbone and dioxaborolane maleimide as the cross-linkable moiety were studied in both the molten and semicrystalline states. We observed that PE vitrimers macroscopically phase separated into dioxaborolane maleimide-rich and -poor regions and characterized the extent of phase separation by optical transmission measurements. This phase separation can explain the relatively low insoluble fractions and overall crystallinities of PE vitrimers. Using synchrotron-sourced small-angle X-ray scattering (SAXS), we discovered that PE vitrimers and their linear…

Photopolymerization under near-infrared (NIR) light is challenging due to the low energy of the absorbed photon but, if successful, presents significant advantages. For example, this lower energy wavelength is safer than UV light that is currently the standard photocuring light source. Also, NIR allows for a deeper light penetration within the material and therefore resulting in a more complete curing of thicker materials containing fillers for access to composites. In this study, we report the use of three-component systems for the NIR photopolymerization of methacrylates: (1) a dye used as a photosensitizer in the NIR range, (2) an iodonium salt as a photoinitiator for the free radical polymerization of the (meth)acrylates, and (3) a phosphine to prevent polymerization inhibition due to the oxygen and to regenerate the dye upon irradiation. Several NIR-absorbing dyes such as a cyanine borate and a silicon–phthalocyanine are presented and studied. Systems using borate dyes resulted in methacrylate monomer conversion over 80% in air. We report three types of irradiation system:…

A series of novel phosphaphenanthrene/phenylsiloxane bigroup macromolecules (DDSi- n ) were synthesized and applied to obtain high-performance epoxy thermosets. DDSi- n macromolecules simultaneously enhanced the anti-impact and flame-retardant performance of epoxy thermosets. The impact strength of the DDSi- n -containing thermoset (DDSi- n /EP) was maximally increased by nearly 140% in 8% DDSi-1/EP because of the flexible phenylsiloxane block and the polar phosphaphenanthrene group interacting with matrix in DDSi- n macromolecules. Meanwhile, the evidently elevated anti-ignition and self-extinguishing performance, the suppressed combustion heat, and the enhanced charring capability of DDSi- n /EP were all caused by the flame-retardant group synergistic effect of phosphaphenanthrene and phenylsiloxane groups of DDSi- n macromolecules in thermosets. Compared with the individual phosphaphenanthrene or phenylsiloxane group in monogroup contrasts, the phosphaphenanthrene and phenylsiloxane groups in bigroup DDSi- n macromolecules were disclosed to synergistically work to toughen and…

This study presents a new framework for extracting single ion diffusion coefficients in ion exchange membranes from experimental ion sorption, salt permeability, and ionic conductivity data. The framework was used to calculate cation and anion diffusion coefficients in a series of commercial ion exchange membranes contacted by aqueous NaCl solutions. Counterion diffusion coefficients were greater than co-ion diffusion coefficients for all membranes after accounting for inherent differences due to ion size. A model for ion diffusion coefficients in ion exchange membranes, incorporating ideas from counterion condensation theory, was proposed to interpret the experimental results. The model predicted co-ion diffusion coefficients reasonably well with no adjustable parameters, while a single adjustable parameter was required to accurately describe counterion diffusion coefficients. The results suggest that for cross-linked ion exchange membranes in which counterion condensation occurs condensed counterions migrate along the polymer backbone and contribute to a current in the presence of…

The use of soybean oil or its derivatives to toughen polylactide (PLA) usually leads to limited toughening efficiency, due to the incompatibility between toughening agents and parent PLA. Herein, we report a dynamic vulcanization method to toughen PLA using sebacic acid cured epoxidized soybean oil (VESO), a fully sustainable and biodegradable component. A series of sebacic acid cured epoxidized soybean oil precursors (SEPs) were prepared with different carboxyl/epoxy equivalent ratio ( R ), which consequently dictates the chemical structure and the morphology of PLA/VESO blends after the dynamic vulcanization. We demonstrated that the chemical structure of VESO plays a critical role in the compatibility, morphology, and toughness of the PLA/VESO blends. By optimizing the R -value, supertoughened PLA blends can be obtained, as evidenced by the significant improvement in the tensile toughness (up to 150.6 MJ/m 3 ) and the impact strength (up to 542.3 J/m). The results of the toughening mechanism from the morphology study confirm that the chemical structure of VESO is the key…

Organocatalysts derived from thioureas and amines exhibit high functional group tolerance and extraordinary selectivities for ring-opening relative to chain transesterification. The modest activities of the thiourea/amine catalysts prompted a detailed investigation of ureas and thiourea with organic bases for the ring-opening polymerization of lactones. An array of ureas or thioureas and organic bases were evaluated to assess the effect of the acidity of the urea (thiourea) and the basicity of the base cocatalyst on the activity for ring-opening polymerization. These studies reveal that for a given urea or thiourea stronger bases lead to faster rates. For a given base, the observed catalytic activity is highest when the acidity of the (thio)urea is closely matched with that of the B–H + . For ureas and thioureas of comparable acidity, the urea/base catalyst systems are considerably more active than the corresponding thiourea/base systems. These results are consistent with two mechanisms: one mediated by deprotonated (thio)urea anions when (thio)ureas are combined with bases of…

Selenium is a semimetallic element lying in group XVI of the periodic table with its chemical properties resembling sulfur. But owing to its relatively low electronegativity and large atomic radius compared with sulfur, selenium also shows unique properties. This feature endows selenium-containing compounds with high reactivity and sensitivity. Although organic selenium chemistry has been developing very fast, the successful introduction of selenium into polymer science is rather scarce. Fortunately, we have seen a drastic rising trend in the area of selenium-containing polymers over the past decade. In this Perspective, the synthetic routes of selenium-containing polymers are summarized, and their unique stimuli-responsive properties are elaborated on, together with their diverse applications in the field of adaptive and biomedical materials.

Abstract Late-transition-metal catalysts have great potentials to incorporate polar comonomers during olefin polymerization. The preparation of polar-functionalized polyolefins with different microstructures and topologies is a highly fascinating concept. In this contribution, we demonstrate this possibility through palladium-catalyzed ethylene copolymerizations with polar-functionalized α-olefins and their terpolymerizations with α-olefins. A phosphine–sulfonate–palladium catalyst (PO-Pd) afforded highly linear polyethylene during ethylene homopolymerization. Linear low-density polyethylene (LLDPE) was obtained from the PO-Pd-catalyzed copolymerizations of ethylene with α-olefins; in these copolymerizations, the partial or complete replacement of α-olefins with polar-functionalized α-olefins led to the formation of polar-functionalized LLDPE (P-LLDPE). A specially designed α-diimine palladium catalyst (NN-Pd) afforded polyethylenes with tunable branching densities (16–37 per 1000 carbon atoms), melting points (101–113 °C), and densities (0.89–0.92 g/cm3), which closely resemble…

Abstract The inherent shortcomings of polylactide (PLA) including brittleness, low glass transition temperature, and melt strength during processing were addressed through a facile melt blending of PLA with polybutadiene-g-poly­(styrene-co-acrylonitrile) (PB-g-SAN) core–shell impact modifier and poly­(methyl methacrylate) (PMMA). Highly tough PLA-based ternary blends with drastically enhanced glass transition temperature (≈ 21 °C) and melt strength were successfully prepared. The effect of PMMA content (ranging from 0 to 30 wt %) on the phase miscibility, morphology, mechanical properties, thermal behavior, rheological properties, and toughening mechanisms of PLA/PB-g-SAN/PMMA blends with 30% PB-g-SAN was systematically investigated. It was found that PMMA can effectively tune the interfacial interactions, phase morphology and performance of incompatible PLA/PB-g-SAN blend owing to its partial miscibility with PLA matrix and miscibility with SAN shell of PB-g-SAN, as evidenced by DMTA analysis. Increase in PMMA content promoted the phase adhesion and dispersion state of PB-g-SAN…

We present detailed studies of ionic conductivity in several polymerized ionic liquids (PolyILs) with different size of mobile ions. Presented analysis revealed that charge diffusion in PolyILs is about 10 times slower than ion diffusion, suggesting strong ion–ion correlations that reduce ionic conductivity. The activation energy for the ion diffusion shows a nonmonotonous dependence on the mobile ion size, indicating a competition between Coulombic and elastic forces controlling ion transport in PolyILs. The former dominates mobility of small ions (e.g., Li), while the latter controls mobility of large ions (e.g., TFSI). We propose a simple qualitative model describing the activation energy for the ion diffusion. It suggests that an increase in dielectric constant of PolyILs should lead to a significant enhancement of conductivity of small ions (e.g., Li and Na).

A thorough vibrational spectroscopy and molecular modeling study on poly(ethylene 2,5-furandicarboxylate) (PEF) explores its conformational preferences, in the amorphous and crystalline regions, while clarifying structure–property correlations. Despite the increasing relevance of PEF as a sustainable polymer, some of its unique characteristics are not yet fully understood and benefit from a deeper comprehension of its microstructure and intermolecular bonding. Results show that in the amorphous domains, where intermolecular interactions are weak, PEF chains favor a helical conformation. Prior to crystallization, polymeric chains undergo internal rotations extending their shape in a zigzag pattern—an energetically unfavorable geometry which is stabilized by C–H···O bonds among adjacent chain segments. The zigzag conformation is the crystalline motif present in the α and β PEF polymorphs. The energy difference among the amorphous and crystalline chains of PEF is higher than in PET poly(ethylene terephthalate) and contributes to PEF’s higher crystallization temperature. The 3D…

Polyester synthesis from the alternating copolymerization of epoxides with cyclic anhydrides via a metal-free route remains a key challenge. This work reports the development of a highly active organocatalytic route for the copolymerization of a spectrum of epoxides and cyclic anhydrides. Fully alternating polyesters were synthesized by a variety of organic Lewis acid–base pairs including organoboranes and quaternary onium salts. The effect of the acidity, type, and size of Lewis pairs on the catalytic activity and selectivity of the copolymerization is presented. The undesirable transesterification and etherification were effectively suppressed even in the case of complete conversion of the cyclic anhydride. This could be ascribed to the formation of a unique tetracoordinate bond-carboxylate (or alkoxide) anion. The Lewis pairs are highly active, with a turnover frequency of 102 and 303 h –1 for the copolymerization of propylene oxide with maleic anhydride and phthalic anhydride, respectively, at 80 °C. Block polyester with narrow polydispersity of 1.05 was achieved via a…

We report mechanistic investigations into aqueous visible-light reversible addition–fragmentation chain transfer (RAFT) polymerizations of acrylamides using eosin Y as a photoinduced electron-transfer (PET) catalyst. The photoinduced polymerization was found to be dependent upon the irradiation wavelength and reagents, where either reduction or oxidation of the PET catalyst leads to inherently different initiation and reversible-termination steps. Using blue light, multiple mechanisms of initiation are observed, depending on the presence or absence of a sacrificial reducing agent. Using green light, both an oxidative and a reductive PET initiation mechanism can be pursued. Investigations into the role of PET catalyst, wavelength, and reducing agent demonstrated that precise polymers with predictable molecular weights are best realized under an oxidative PET-RAFT mechanism. Therefore, this study provides fundamental insight into visible-light RAFT photopolymerizations and the role of eosin Y as a photoredox catalyst.

By examining structurally similar halogenated xanthene dyes, this study establishes a guiding principle for resolving structure-property- performance relationships in the photocontrolled PET-RAFT polymerization system (PET-RAFT: photoinduced electron/energy transfer-reversible addition-fragmentation chain transfer). We investigated the effect of the halogen substituents on the photophysical and electrochemical properties of the xanthene dyes acting as photocatalysts and their resultant effect on the performance of PET-RAFT polymerization. Consideration of the structure- property-performance relationships allowed design of a new xanthene photocatalyst, where its photocatalytic activity (oxygen tolerance and polymerization rate) was successfully optimized for PET-RAFT polymerization. We expect that this study will serve as a theoretical framework in broadly guiding the design of high performance photocatalysts for organic photocatalysis.

We investigate the effect of pulling point location on the mechanochemical activation of two isomers of spiropyran in cross-linked polymeric materials through computational calculations and in situ fluorescence measurements. The threshold stress and strain required to activate the spiropyran mechanophores under tensile load are characterized. For both spiropyran isomers, applied stress favors the activated merocyanine states; however, despite differences in mechanochemical behavior predicted by quantum chemical calculations and previous single molecule experiments, both spiropyran isomers exhibit similar mechanochemical reactivity in bulk polymeric materials. The kinetics of the spiropyran–merocyanine transition under different tensile stresses are also examined. Overall, we find that varying the pulling geometry on the spiropyran mechanophore has only a minimal effect on the mechanical activation in bulk polymeric materials due to the complex nature of the macroscopic system.

Ring-opening polymerization (ROP) is a versatile approach to well-defined polymers. Achieving both high efficiency and precise control remains a major challenge. We herein report room-temperature living ROP of epoxides catalyzed by combined organobase and triethylborane (Et 3 B) with water or alcohols as initiators. Extremely high catalytic efficiency (turnover frequency up to 6000 h –1 ) is exhibited despite the relatively mild Lewis basicity and acidity, and the catalyst loading can be minimized to 44 ppm. Poly(ethylene oxide) products are noncytotoxic toward a variety of cell lines even without purification. Poly(propylene oxide) with molar mass as high as 210 kg mol –1 and low dispersity ( Đ M < 1.1) can be achieved owing to the absence of detrimental transfer reactions. The chemoselectivity allows the catalyst to be readily applied to living ROP of glycidyl ethers, tailored synthesis of diverse functional/block/nonlinear (co)polyether structures, and one-pot one-catalyst synthesis of polyether-based polyurethane. Our study reveals the effective cooperation modes of the Lewis…

The development of polyimides (PIs) with a superheat resistance and a high thermal dimensional stability is required urgently for application in the rapidly growing area of flexible-display substrates. Based on an enhanced intermolecular interaction, 2,2′- p -phenylenebis(5-aminobenzimidazole) (DP) that contains bis-benzimidazole was synthesized, and two series of its copolyimides (PI-a and PI-b) were prepared by copolycondensation with 5-amino-2-(4-aminobenzene)benzimidazole (PABZ) and 5-amino-2-(3-aminobenzene)benzimidazole ( i -PABZ), respectively. The high density and packing coefficient of the resulting PIs caused by the strong intermolecular interaction from the hydrogen bonds and the charge-transfer complex provided the PI films with a very high glass-transition temperature ( T g > 450 °C) and an extremely low coefficient of thermal expansion (CTE) below 10 ppm/K for PI-a. Such good thermal properties expand their application as high thermostable materials. Furthermore, the PI-b had a higher T g than PI-a, whereas the latter had lower CTE values because of the configuration…

Conjugated microporous polymers (CMPs) exhibit great potential for photocatalytic hydrogen generation due to their tunable electronic structure. The rational molecular design is a key point for developing an efficient CMP photocatalyst. Herein, we developed two CMPs photocatalysts via the copolymerization from pyrene and dibenzothiophene- S, S -dioxide building blocks. The effect of the linking pattern of the building block of dibenzothiophene- S, S -dioxide on the photocatalytic hydrogen evolution was explored. The polymer of PyDOBT-1 with 3,7-linking pattern shows a superior photocatalytic performance to PyDOBT-2 with 2,8-linking pattern because the 3,7-linking pattern enhances the conjugation chain length and improves the coplanarity of the polymeric backbone, which facilitate the charges migration along the polymer chain. As a result, the bare PyDOBT-1 shows an impressive visible light activity with a hydrogen evolution rate (HER) of 5697 μmol h –1 g –1 . Notably, an outstanding HER of 12986 μmol h –1 g –1 was also obtained by the Pt-modified PyDOBT-1 under the full-arc spectrum…

Abstract The rheology of water-soluble polyelectrolytes at intermediate and high concentrations is controlled by entanglement, hydrophobic, and electrostatic interactions, whose influences are difficult to isolate. We investigate the rheology of semidilute solutions of sodium carboxymethyl cellulose (NaCMC) with molecular weight Mw ≃ 2.5 × 105 g/mol and varying degree of substitution (DS) as a function of polymer concentration in various solvent media: salt-free water (long-ranged electrostatic interactions), 0.5 M aqueous NaCl (screened electrostatics), and 0.5 M aqueous NaOH (screened electrostatics, diminished hydrophobic interactions) in order to selectively examine the role played by these different interactions. Decreasing DS is found to decrease solubility and induce partial aggregation and eventual gelation. In salt-free and 0.5 M NaCl solution, NaCMC with DS ≃ 1.2 exhibits hydrophilic polyelectrolyte and neutral polymer in good solvent behavior, respectively. Decreasing DS to ≃0.7–0.8 leads to hydrophobic behavior in both media, becoming weak gels at high concentrations. In…

Circularly polarized luminescent (CPL) materials are currently drawing ever-increasing interest. This contribution reports the first success in simply combining chiral helical substituted polyacetylenes (HSPAs) with achiral luminophores to fabricate CPL materials demonstrating a high dissymmetry factor ( g lum ) up to 10 –1, despite neither covalent nor noncovalent interactions occurring between the two components. Circularly polarized scattering and fluorescence-selective absorption mechanisms are proposed for the generation of CPL, and a “matching rule” is further established for selecting chiral polymers and achiral luminophores for the purpose. Taking advantage of the circularly polarized scattering effect, full-color tunable CPL materials are prepared from the combination of achiral fluorescent dyes and chiral HSPAs. Following the fluorescence-selective absorption mechanism, functional composite films with on–off and switchable CPL performance are fabricated. Also, remarkably, the g lum value in the prepared materials can reach up to +0.323. The present study provides a simple,…

Abstract Mechanistic behavior and flow properties of cellulose nanofibers (CNFs) in aqueous systems can be described by the crowding factor and the concept of contact points, which are functions of the aspect ratio and concentration of CNF in the suspension. In this study, CNFs with a range of aspect ratio and surface charge density (380–1360 μmol/g) were used to demonstrate this methodology. It was shown that the critical networking point of the CNF suspension, determined by rheological measurements, was consistent with the gel crowding factor, which was 16. Correlated to the crowding factor, both viscosity and modulus of the systems were found to decrease by increasing the charge density of CNF, which also affected the flocculation behavior. Interestingly, an anomalous rheological behavior was observed near the overlap concentration (0.05 wt %) of CNF, at which the crowding factor was below the gel crowding factor, and the storage modulus (G′) decreased dramatically at a given frequency threshold. This behavior is discussed in relation to the breakup of the entangled flocs and…

Atom transfer radical polymerization was employed to induce the living polymerization of an azobenzene-containing monomer, 10-[4-(4-hexylphenylazo)phenoxy]decyl acrylate, with the resulting polyacrylate and the corresponding polymethacrylate undergoing a reversible solid–liquid phase transition under isothermal conditions caused by the photoinduced change of the azobenzene moiety shape. Irradiation-induced property changes were investigated by nuclear magnetic resonance, ultraviolet–visible (UV–vis) absorption spectroscopy, and dynamic viscoelasticity measurements, with focus on the effects of the main chain chemical structure and molecular weight. Azobenzene moiety photoisomerization and the concomitant phase transition were faster for the polyacrylate than for the polymethacrylate, which indicated the strong influence of the main chain structure. Finally, phototuning of the adhesion strength using azopolymer-bonded glass substrates was studied by single lap shear tests, with the maximum adhesion strength of >3 MPa being comparable to that of commercial hot-melt adhesives.…

Two-way shape-memory polymers (2W-SMPs) show great potential in actuating applications such as robotics due to their reversibility; indeed, multiresponsive 2W-SMPs are more expected. Inspired by the fascinating adhesion effects of mussels, we herein describe a metallo-supramolecular poly(ε-caprolactone) (PCL)-based network constructed around catechol chemistry, leading to excellent thermal/magnetic/light-responsive two-way shape-memory effects (2W-SME) as well as self-healing capacity. These hybrid networks get readily self-assembled upon metal coordination interaction between superparamagnetic iron oxide nanoparticles (Fe 3 O 4 NPs) and catechol-telechelic PCL. The incorporation of Fe 3 O 4 NPs may act as the strong netpoints which allow the networks with excellent thermal-responsive one-way (1W) and 2W-SME, due to the ability of the semicrystalline PCL segments to present both crystallization-induced elongation (CIE) and melting-induced contraction (MIC) under constant stress. As a multifunctional medium, moreover, it also endows the hybrids with the magnetic-responsive 2W-SME in…

As an injectable and biodegradable hydrogel, thermogels of amphiphilic block copolymers of polyester and polyether in water show great potential in biomedical fields. It is challenging to reveal the mechanism behind the reversed thermogelling with sol–gel transition upon heating. Herein, a computer simulation and corresponding experiments are combined to examine aqueous systems of amphiphilic diblock copolymer of methoxypoly(ethylene glycol) and poly( d, l -lactide- co -glycolide). We synthesized the copolymer via ring-opening polymerization and characterized the thermogelling behavior of its aqueous solution by 3D dynamic light scattering and diffusing wave spectroscopy. Fluorescence resonance energy transfer and 13 C NMR spectroscopy etc. were also adopted to explore the structure change during thermogelation. A dynamic Monte Carlo simulation was performed for a corresponding multichain system. A new type of micelle, the semi-bald micelle, was first proposed as the precursor for thermogelling and was confirmed from both simulations and experiments. We demonstrate that the…

This work details a novel polyurethane liquid crystal elastomer (PULCE) with exchangeable carbamate functional groups that enable programming of a uniformly aligned monodomain sample through the application of external stress and simultaneous activation of dynamic bond exchange of the carbamate. PULCEs were synthesized using a thiol-Michael addition reaction, and the reversion of the carbamate group was observed by real-time FT-IR and mechanical analysis. Two independent phase transitions (isotropic–nematic and nematic–smectic) were employed to actuate two-way autonomous strains and multiple shape memory effects in a single system. In addition, thermally activated bond exchange engineered into the network transformed the permanent configuration of the material into various complex shapes. The programmed network topology and bond exchange conditions controlled the two-way autonomous shape changes. Coupling the shape memory effect of the polymer network with the plasticity induced by the thermally activated dynamic covalent chemistry in shape changing and shape memory materials will…

We introduce visible light induced dynamic covalent chemistry as a powerful reversible ligation tool based on a wavelength-dependent photon efficiency analysis (WPEA). We demonstrate by a monochromatic wavelength scan of the reversible dimerization of styrylpyrene at constant photon count that the system is most effective in its forward reaction at 435 nm, while the highest reverse reaction efficiency is observed at 330 nm. Critically, these optimum wavelengths are not accessible by inspection of the UV/vis spectra of the monomer and the dimer. Application of the identified reaction conditions enabled an entirely λ-orthogonal photoreversible polymer ligation using visible light, including with readily available light sources. The current study thus makes a [2 + 2] reaction system applicable in the critical visible light regime based on quantitative wavelength resolved data for applications in recodeable surface design in biological environments as well as reprogrammable materials systems.

The environmental impact of industrially important plastics can be minimized by using renewable feedstocks and preparing biodegradable polymers. A significantly more meaningful strategy is the utilization of alternating copolymerization of epoxides and cyclic anhydrides or lactone or CO 2 to provide degradable polyesters or polycarbonates. Herein, we report a versatile and efficient catalyst system based on dinuclear chromium complex bearing biphenol linking bridge for copolymerizing epoxides with cyclic anhydrides or CO 2 or dihydrocoumarin (DHC), affording various degradable copolymers with perfectly alternating structure and narrow molecular weight distribution. Most of the polyesters from DHC are typical semicrystalline materials, being beneficial to the potential application of aliphatic polyesters as structural materials. Notably, this dinuclear chromium catalyst system was also discovered to be very efficient in the one-pot terpolymerization of cyclohexene oxide/phthalic anhydride/CO 2, cyclohexene oxide/phthalic anhydride/DHC, or cyclohexene oxide/CO 2 /DHC, providing…

We report on the synthesis of poly(diethylene oxide- alt -oxymethylene), P(2EO-MO), via cationic ring-opening polymerization of the cyclic ether monomer, 1,3,6-trioxocane. We use a combined experimental and computational approach to study ion transport in electrolytes comprising mixtures of P(2EO-MO) and lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) salt. Mixtures of poly(ethylene oxide) (PEO) and LiTFSI are used as a baseline. The maximum ionic conductivities, σ, of P(2EO-MO) and PEO electrolytes at 90 °C are 1.1 × 10 –3 and 1.5 × 10 –3 S/cm, respectively. This difference is attributed to the T g of P(2EO-MO)/LiTFSI (−12 °C), which is significantly higher than that of PEO/LiTFSI (−44 °C) at the same salt concentration. Self-diffusion coefficients measured using pulsed-field gradient NMR (PFG-NMR) show that both Li + and TFSI – ions diffuse more rapidly in PEO than in P(2EO-MO). However, the NMR-based cation transference number in P(2EO-MO) (0.36) is approximately twice that in PEO (0.19). The transference number measured by the steady-state current technique, t +,ss, in…

Although intermolecular charge transport is known to occur via π–π stacking, the influence of π–π stacking on the mechanical properties of polymers has received little attention compared with other dynamic noncovalent interactions. Herein, we demonstrate a method to enhance stretchability via lowering crystallinity and increasing π–π stacking of thiophene-based random copolymer chains, which causes π–π stacking-induced polymer networks to form within the fully conjugated semiconducting polymer matrix. The polymer networks contain coiled amorphous chains that aid energy dissipation when the polymer film is subjected to strain; furthermore, the π–π stacking prevents the chains from irreversible sliding out of place due to the applied strain and provides interchain charge transport. Consequently, we are able to improve the polymer’s mechanical properties such as elongation at break, tensile strength, and toughness along with charge mobility. Additionally, our polymer shows great tolerance to a 40% strain without a decrease in mobility while maintaining a stable electrical performance…

The macroscopic mechanical response of polymers can be traced down to the microscale physics of the network by using a statistical approach for the description of the configuration state of the polymer chains. In this paper we present a micromechanical model to capture the macroscopic behavior of polymers by tracking the evolution of a distribution function describing chain configurations, more specifically the statistics of the end-to-end distance on the network chains. Damage, manifested in the softening and hysteresis under cyclic loading, is accounted for through the scission of chains, whose occurrence is evaluated on the basis of the probability of failure, also settled in the configuration space. The proposed micromechanical model can easily accommodate also the mechanics of dynamic network with reversible cross-links, thereby providing a general and physics-based approach to the study of polymers and polymer-like materials.

Abstract Combinatorial and high throughput (HTP) methodologies have long been used by the pharmaceutical industry to accelerate the rate of drug discovery. HTP techniques can also be applied in polymer chemistry to more efficiently elucidate structure–property relationships, to increase the speed of new material development, and to rapidly optimize polymerization conditions. Controlled living/radical polymerization (CLRP) is widely employed in the preparation of potential materials for bioapplications being suitable for a large variety of polymeric materials with various architectures. The versatility of CLRP makes it an ideal candidate for combinatorial and HTP approaches to research, and recently, the development of oxygen tolerant CLRP techniques has greatly simplified the methodology. In this Perspective, we provide an overview of conventional CLRP, including automated parallel synthesizers, as well as oxygen tolerant CLRP applications for HTP polymer research.

Poly(ethylene glycol)s (PEG) are widely and intensely used in the pharmaceutical industry and biomedical applications, and due to this fact, antibodies have recently been reported. Poly(2-oxazoline)s (POx) are promising candidates for potential replacement of PEG in related applications, and as such, their hydrodynamic properties and characteristics derived from light scattering experiments are important to reconcile their behavior in solution. In this study, we have investigated the molecular hydrodynamic characteristics of poly(2-methyl-2-oxazoline)s and poly(2-ethyl-2-oxazoline)s in the pharmaceutical molar mass range as base candidates for such applications, prepared by cationic ring-opening polymerization in a microwave reactor. A combined viscometry and sedimentation–diffusion analysis by using sedimentation velocity experiments in an analytical ultracentrifuge includes (i) the study of intrinsic viscosities, (ii) sedimentation coefficients, and (iii) derived translational diffusion coefficients. These characteristics are then interrelated through hydrodynamic invariants that…

We investigate a high throughput approach to polymer synthesis by employing photoinduced electron/energy transfer–reversible addition-fragmentation chain transfer (PET-RAFT) polymerization. Polymerization of a broad range of monomers, including acrylates, methacrylates, acrylamides, and styrenic monomers, was achieved directly in a multiwell plate by employing 5,10,15,20-tetraphenylporphine zinc (ZnTPP) as a photocatalyst under yellow LED light. Various parameters such as monomer concentration and degree of polymerization were investigated with respect to their effect on polymerization rate and the degree of control over the molecular weight and molecular weight distribution. Finally, the synthesis of well-defined multiblock copolymers (up to a hexablock copolymer) was shown to be achievable entirely within a multiwell plate without any intermediate purification. The versatility and ease of this oxygen tolerant polymerization in high throughput formats make it an excellent technique for the generation of polymer arrays.