The 50 most-cited articles in Journal of Applied Polymer Science, 2018

ABSTRACT Stealth or low observable technology has been one of the most critical requirements for military aviation sector to counter the ever‐advancing target detection technologies worldwide. Among many, Radar, which operates in the broadband spectrum, is one of the principal threats, which measures the radar cross section (RCS) of the aircraft. Hence, researchers are putting immense efforts to develop low RCS materials based on polymer matrix composites (PMCs) called as radar absorbing structures (RAS), to replace highly reflective conventional metallic aircraft structures. Though many researchers have been successful in RAS realization using radar absorbing materials (RAMs) as fillers, this review article reckons the state‐of‐the‐art advanced research on the realization of RAS using a combination of RAMs and multilayered grid devices such as, frequency selective surfaces, circuit analog absorbers, metamaterials, and so on, and their effect on mechanical properties to deliver superior performance RAS for stealth aircrafts. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 ,…

ABSTRACT Thermoset resins have been extensively utilized as an adhesive for electronic devices. In particular, semiconductor packaging materials between chips/substrates require electrical interconnections by using deoxidizing agents along with thermoset adhesives. In this study, a facile combination of hydroxyl‐functionalized epoxy and cyclohexane‐structured cyclic anhydrides produced curable acidic moieties, thereby allowing synchronous deoxidizing and curing without the use of a deoxidizing agent. By contrast, unitary cyclic anhydrides rarely presented acidic moieties, probably due to their rapid networkable reactivity caused by structural flexibility once opened, which was detected and quantified by spectroscopic analyses. This binary system in the absence of additional deoxidizing agents achieved the complete wetting of common Sn‐based solders via chip bonding systems due to the generated acidic moieties. The binary mixture also showed an increased glass transition temperature of 110 °C and enhanced Young's modulus of 1.6 GPa, relative to the ternary mixture (85 °C and 0.8 GPa)…

ABSTRACT The main objective of this work is to study the effect of chemical treatment on the thermal properties of hybrid natural fiber‐reinforced composites (NFRCs). Different chemical treatments [i.e., alkalized and mixed (alkalized+ silanized)] were used to improve the adhesion between the natural fibers (jute, ramie, sisal, and curauá) and the polymer matrix. A differential scanning calorimetry, thermogravimetry, and a dynamic mechanical analysis were performed to study the thermal properties of hybrid NFRC. It was found that the chemical treatments increased the thermal stability of the composites. Scanning electron microscopy images showed that the chemical treatments altered the morphology of the natural fibers. A rougher surface was observed in case of alkali treated fiber, whereas a thin coating layer was formed on the fiber surface during the mixed treatment. However, for some fibers (i.e., sisal and rami), the chemical treatment has a positive impact on the composite properties, whereas for the jute and curauá composites, the best behavior was found for untreated fibers.…

ABSTRACT Phthalate esters received a considerable attention owing to its various applications and the harmful health effects resulting from phthalate exposure; thus, finding an alternative to phthalate derivatives became a necessity. Phthalate esters are commonly used as plasticizer in polymer formulation; in particular for poly(vinyl chloride) (PVC) formulation. According to the researches in the last 18 years, epoxidized vegetable oils are one of the alternatives that are strongly encouraged to substitute phthalate esters since they were proven to be valid in various applications, eco‐friendly and sustainable resource. However, most of the production practices for epoxidized vegetable oil are via conventional epoxidation that concentrates on a catalyst that is homogeneous and non‐reusable. This type of catalyst, however, causes several problems later in the process. Therefore, the selective epoxidation of vegetable oils process requires new catalytic systems that are more aligned with the green chemistry principles. This article reviews the harmful health effects associated with…

ABSTRACT There has been a steady progress in developing synthetic fibers in the past few years. Bicomponent fibers and nanofibers in a core/shell (C/S) configuration, including two dissimilar materials have presented unusual potential for use in many novel applications. These fibers can be produced using a variety of materials via different techniques i.e., coaxial melt spinning and electrospinning. In this review, we discuss the recent advances in C/S fibers and nanofibers’ production. The first part has been assigned to the bicomponent fibers manufacturing technology, while production and applications of C/S nanofibers have been described in the second part. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci.2018,135, 46265.

ABSTRACT Polyurethane/water glass (PU/WG) grouting materials were prepared in presence of different proportions of catalyst. The effects of catalyst on the mechanical properties, thermal properties, and chemical cross‐sectional morphologies of the grouting materials were also investigated. Catalyst addition can significantly increase the chemical reaction rate, reduce the gel time and curing time, and improve the thermal stability of PU/WG grouting materials. It was found that the grouting material containing 0.1 wt % BDMA + 0.1 wt % DBTDL demonstrated high fluidity, short curing time, and high early‐stage and late‐stage (up to 66.1 MPa) compression strengths. However, when the content of the added catalyst was equal to 0.5 wt %, fine cracks were formed in the material structure accompanied by the detachment of spherical particles from the PU matrix, which significantly deteriorated its mechanical properties. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46460.

ABSTRACT Cellulose nanocrystal (CNCs)‐reinforced poly(lactic acid) (PLA) nanocomposites were prepared using twin screw extrusion followed by injection molding. Masterbatch approach was used to achieve more efficient dispersion of CNCs in PLA matrix. Modified CNCs (b‐CNCs) were prepared using benzoic acid as a nontoxic material through a green esterification method in a solvent‐free technique. Transmission electron microscopy images did not exhibit significant differences in the structure of b‐CNCs as compared with unmodified CNCs. However, a reduction of 6.6–15.5% in the aspect ratio of b‐CNCs was observed. The fracture surface of PLA‐b‐CNCs nanocomposites exhibited rough and irregular pattern which confirmed the need of more energy for fracture. Pristine CNCs showed a decrease in the thermal stability of nanocomposites, however, b‐CNCs nanocomposites exhibited higher thermal stability than pure PLA. The average storage modulus was improved by 38 and 48% by addition of CNCs and b‐CNCs in PLA, respectively. The incorporation of b‐CNCs increased Young's modulus, ultimate tensile…

ABSTRACT The global shift towards biodegradable composite has made polysaccharides a green alternative to synthetic polymers owing to their biocompatibility, sustainability, and ecofriendly biomaterials. Despite the limitations in their applications, many studies have validated the effectiveness of using organic or inorganic fillers to ameliorate their mechanical and barrier properties. However, the understanding of how polysaccharides matrix is enhanced by fillers is still inexplicit. Hence, it is imperative to review the effects of using inorganic and organic fillers in some prominent polysaccharides in terms of mechanical and water barrier properties while taking into account the function of filler morphology, size and loading. Although it is intricate to indicate the best filler used for each of the polysaccharides matrices, this review served as a “food for thought” on the established works of enhanced‐matrix filler combinations aimed at improving the mechanical and barrier properties of biodegradable films based on neutral or negatively charged polysaccharides‐based composite…

ABSTRACT Concern about environmental issues has motivated research into the development of biodegradable packaging from renewable sources. Natural polymers such as starch constitute a good alternative for diminishing the use of nonbiodegradable and nonrenewable components in the packaging industry. However, depending on the botanical source, films with different properties are formed. The aim of this study was to evaluate the film‐forming capacity of different starch sources (cassava, corn, potato, and wheat) by casting with starch contents from 2 to 6%. Principal component analysis methodology was used to evaluate the correlation between the formulations and their physicochemical and mechanical properties. It was not possible to produce continuous films based on potato starch, probably because of its very low amylose content (10%). The corn‐, cassava‐, and wheat‐starch‐based films were characterized by their thicknesses (0.06–0.22 mm), moisture contents (19–26%), water solubilities (13.7–26.5%), water‐vapor permeabilities (WVPs; 0.19–0.48 g mm h−1 m−2 kPa−1), wettabilities…

ABSTRACT Silicon rubbers are widely used in a variety of products ranging from cooking utensils and electronics to medical devices and implants. Recently, they have sparked an interest among soft robotics researchers as they can be easily formed into various shapes and actuated in a relatively fast and easy way. In this article, we examine the nonlinear elastic response of a silicon rubber, Ecoflex, under both compressible and incompressible constraints. An experimental test on a uniaxial tension indicates a slight compressibility, and the compressibility increases with stretching. Five different constitutive material models are considered to describe the nonlinear elastic responses of Ecoflex under both compressible and incompressible conditions. In addition, finite element (FE) analysis is presented to analyze multiaxial response of structures or devices made of Ecoflex under complex boundary conditions. This study highlights the variations in the multiaxial response of structures at large deformations from different constitutive models under different compressible and…

ABSTRACT To mitigate the dust dispersion pollution in the open‐pit coal mines, this study experimentally develops a novel environmentally friendly coal dust suppressant. The experiment uses naturally biodegradable soybean protein isolate (SPI) as the main material and utilizes anion surfactant sodium dodecyl sulfate (SDS) to modify SPI. In the carboxymethylcellulose sodium and sodium silicate and other auxiliary agents, this process produces gives rise to the SDS‐SPI coal dust suppressant. Experimental characterization of the developed dust suppressant reveals that the viscosity of the 5% dust suppressant solution can reach 24.6 mPa s. Correspondingly, the compressive strength reaches 0.48 MPa, and the dust suppression efficiency can reach 93.47% with the presence of force 9 wind. Furthermore, this study uses Fourier‐transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM) to analyze the dust suppression mechanism of the developed dust suppressant. It is observed that a layer of compact hardened shell is formed at the surface of the coal powder treated with the…

ABSTRACT Poly(lactic acid) (PLA)/poly(butylene adipate‐co‐terephthalate) (PBAT) blends were compatibilized using epoxidized polyhedral oligomeric silsesquioxanes (Epoxy‐POSS). Three different Epoxy‐POSS types were utilized having mono‐, tri‐, and multi‐epoxides per POSS cage. In order to understand the localization of Epoxy‐POSS types, wetting coefficients were calculated from surface energy measurements. According to scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it was observed that Epoxy‐POSS types mostly located at the interface of PLA/PBAT phases. The compatibilization of PLA and PBAT was shown through the decrease in dispersed particles size and the shifts in glass transition temperatures of phases. Mechanical properties of PLA/PBAT improved in the presence of Epoxy‐POSS types. The Izod impact strength and elongation in tensile test values were maximized when 0.5% monoepoxy‐POSS was used as compatibilizer. The reactions between Epoxy‐POSS and polymers were monitored by Fourier transform infrared (FTIR) analysis and rheology. © 2018 Wiley…

ABSTRACT The ecologically friendly flame retardant melamine polyphosphate (MPP) was prepared and incorporated into linear low‐density polyethylene (LLDPE). The impacts of this halogen‐free flame retardant on the mechanical characteristics of LLDPE were investigated in this research. The flame‐retardant properties were evaluated, and the mechanical properties, including flexural, tensile, compressive, fracture toughness, and shear behaviors, were tested. The weight fraction of the filler material ranges from 5% to 30%. The influence of filler weight content of the produced composites was evaluated by means of a universal testing machine in order to identify their behavior. The flammability of composites was highly improved with the addition of MPP. It was observed that the Young's modulus and flexural modulus increased almost linearly; similarly, the tensile fracture strength and tensile yield strength increased with the increase in MPP weight fraction. The tensile elongation at break decreased sharply between zero and 10% weight fraction, followed by a slight decrease up to 30%…

ABSTRACT Polydimethylsiloxane (PDMS) is one of the most widely employed silicon‐based polymers for its high flexibility, low usage temperature, excellent water resistance, outstanding electrical insulting property, and physiological inert, etc. However, the covalent‐bonded SiO bonds are unable to heal automatically when damaged, which would result in the failure of the materials and devices. Disulfide bond based polymers show high healing efficiency at moderate temperature and have been investigated intensively. Herein, we report a PDMS‐based polyurethane self‐healing polymer (PDMS‐PU) modified with disulfide bonds, which exhibited a reinforced thermal stability, excellent stretchability, and satisfactory self‐healing ability. The effect of different ratio of PDMS and disulfide bond contents on the elastomer properties was investigated. With the increase of PDMS content, the decomposition temperature of the PDMS‐PU‐3 (332 °C) elastomer with highest content of PDMS was increased by 34 °C compared to PDMS‐PU‐1 (298 °C) with lowest content of PDMS and exhibited a largest elongation at…

ABSTRACT Harvesting energy has been attracting the attention of researchers in recent years. This work comprehensively reports the fabrication and characterization of poly(vinylidene fluoride) fiber webs with comparable diameters and diversified surface morphologies (wrinkled, smooth, and porous) based on randomly oriented and aligned fiber webs which are used as active layers to directly make a piezoelectric nanogenerator (PENG). The results show that wrinkled fibers are preferable fiber webs for the PENG owing to their outstanding properties represented by high fibers friction, supreme β phase content (F[β]), and interior pores. Furthermore, we found that the electrical outputs of the PENG based on aligned fiber webs are higher than those based on randomly oriented fiber webs due to the increase in the friction area. The electrical outputs of the PENG based on the aligned wrinkled fiber webs are able to run microelectronic devices when it subjected to a mechanical impact. We believe that our study may inspire the research area for future energy harvesting applications. © 2018…

ABSTRACT The use of flexible films in agriculture has increased intensely in the last 15 years bringing benefits to producers. However, environmental impacts increased due to their incorrect post‐use disposal which leads the degradable films to emerge as an alternative. The production films of poly(butylene adipate‐co‐terephthalate) and poly(lactic acid) reinforced with calcium carbonate (CaCO3) was studied focusing on producing lower cost materials and flexible films. Four different films (reinforcement compositions) were prepared by melt extrusion with 10 and 20 wt % of CaCO3. Mechanical and thermal properties, crystallinity, water absorption, and soil degradation, were evaluated. The addition of reinforcement leads to improved compatibility between the polymers in the matrix, which usually presented phase segregation. The films showed better mechanical properties with the addition of CaCO3. Highly orientated amorphous structures were obtained leading to low water absorption and low degradation in the simulated soil. This low degradation, suggests that the obtained films would be…

ABSTRACT The investigation for natural fibers composites in terms of performance, durability, and environmental impact for structural applications in marine environments is a relevant challenge in scientific and industrial field. On this context, the aim of this work is to assess the durability and mechanical stability in severe environment of epoxy/glass–flax hybrid composites. For the sake of comparison, also full flax and glass epoxy composites were investigated. All samples were exposed to salt–fog environmental conditions up to 60 aging days. Wettability behavior during time was compared with water uptake evolution to assess water sensitivity of hybrid composite configurations. Moreover, quasi‐static flexural and dynamic mechanical analysis were carried to evaluate as aging conditions, laminate configuration influence the surface and mechanical performances stability of the hybrid composites. The addition of glass fibers on flax laminate allows to enhance both flexural strength by 90%, and modulus by 128%, even if these properties are lower than those of full glass laminates.…

ABSTRACT Many efforts have been made to develop modern wound dressings to overcome limitations of traditional ones. Smart nanocomposite hydrogels are appropriate candidates. In this work, a novel responsive nanocomposite hydrogel based on poly(vinyl alcohol)/chitosan/honey/clay was developed and evaluated as a novel wound dressing. The morphology and properties of synthesized nanocomposite hydrogels loaded with honey as a drug model were investigated. The exfoliated morphology of nanocomposite was confirmed by X‐ray diffractometry. Swelling studies were performed at 20 and 37 °C at various pH. The results showed that swelling increased as a result of temperature rise and maximum swelling occurred at a pH of 2. In vitro release of honey was also studied at the same conditions. Corresponding results indicated faster honey release rate at higher pH values. MTT results exhibited no cytotoxicity in nanocomposite hydrogel system. Investigation of antibacterial activity revealed more than 99% antibacterial activity for proposed system. In vivo results confirmed the wound healing ability of…

ABSTRACT During coal transportation, a large amount of coal dust is generated; this not only leads to a massive loss of coal but also causes severe environmental pollution. In this research, we used a chemical modification approach to prepare a highly water‐absorbing dust suppressant. Corn starch, as the main ingredient, was copolymerized with acrylic acid and acrylamide, and acrylic acid and acrylamide were used to form a starch graft copolymer. Subsequently, in this research, we designed a suite of single‐factor experiments using the viscosity as the metric to determine the optimal reaction conditions, which were as follows: mass ratio of acrylic acid to acrylamide = 3:2, neutrality = 50%, reaction time = 3 h, and reaction temperature = 50 °C. Tests were carried out to assess the viscosity, water retention, and anti‐evaporation performance of the dust suppressant. The results indicate that when the dust‐suppressant concentration was 6%, the performance was optimized. Also, the anti‐evaporation behavior of the suppressant improved with the dust‐suppressant concentration. The use of…

ABSTRACT Poly(lactic acid) (PLA) is a biodegradable aliphatic polymer obtained from renewable sources; its main application is in the packaging sector. Electronic components require the use of antistatic packaging that prevents damage and electric shock. As PLA has no conductive characteristics, it requires the addition of allotropic carbon forms such as conductive carbon black to make the polymer less resistive as the dissipative material and making it suitable for the manufacture of antistatic packaging. In this study, PLA was melt blended with 5, 10, and 15 wt % of carbon black. The composites were prepared using a high‐speed mixer. Samples were characterized by Izod impact resistance tests, scanning electron microscopy, thermal properties, electrical characterization, and biodegradation tests in garden soil. The addition of carbon black in the PLA matrix increases the temperature of degradation and decreases the crystallinity degree and the impact resistance of the composites. However, carbon black is a great option to increase the electrical conductivity of PLA. The addition of…

ABSTRACT Poly(vinylidene fluoride) (PVDF) and poly(vinylidene fluoride)‐co‐hexafluoropropylene (PVDF‐HFP) were used to fabricate porous microfiltration membranes via a thermally induced phase separation (TIPS) method, and dibutyl phthalate (DBP) was used as diluent. The effects of polymer concentration on structure and performance were studied in detail. In addition, the effect of incorporation of hexafluoropropylene (HFP) groups on the membrane was also investigated. The formation mechanism was proposed with the assistance of a phase diagram. The results showed that the incorporation of HFP groups resulted in a lower crystallization temperature (Tc) of the polymer/DBP system. In addition, the porosity, pure water flux, and ink solution flux decreased with increasing polymer concentration. In contrast, the water contact angle, ink rejection ratio, and mechanical properties had an increasing tendency. When the polymer concentration was 30 wt %, the obtained membrane was most suitable for microfiltration. Furthermore, the incorporation of HFP groups improved the properties of the…

ABSTRACT Gelatin/chitosan/poly(vinyl alcohol) (PVA) hydrogels were fabricated with different polymer ratio using the freeze‐drying process. The thermal stability, water state, rheological, and cytotoxic properties of the hydrogels were evaluated. Thermogravimetric/differential scanning calorimetry analyses showed a decomposition onset temperature below 242.7 ± 2.7 °C. The samples did not show statistical differences (p < 0.05) on the onset temperature values. Nonfreezing water reached a constant value around of 1 g water/g polymer. Freezing water increased linearly with the increase of the water content independently of the polymer ratio. The hydrogels showed an equilibrium water content from 9 to 13 times their mass. The hydrogels exhibited a solid‐viscoelastic behavior. The elastic modulus was higher with the increase of chitosan concentration (G′ = 22 170 ± 85 Pa) independently of the temperature (5–55 °C). In vitro assay showed that hydrogels are nontoxic in the HT29‐MTX‐E12 cell line. These results indicate that the gelatin/chitosan/PVA hydrogels could be considered for…

ABSTRACT Nanostructured chitosan/polyaniline (CH/PANI) hybrid was synthesized via in situ polymerization of aniline in the presence of chitosan. The CH/PANI hybrid was characterized by FTIR spectroscopy, X‐ray diffraction, thermogravimetric analysis, and scanning electron microscopy. The CH/PANI hybrid had a nanofibrous structure with an average diameter of 70 nm. This hybrid was employed as an ecofriendly and efficient adsorbent with high adsorption capacity for the removal of Acid Green 25 (AG) and methylene blue (MB) from aqueous solutions. AG and MB were used as anionic and cationic model dyes, respectively. The CH/PANI adsorbent showed high dependence on the pH of the medium with an excellent adsorption performance and regeneration manner. The kinetics and adsorption isotherms were studied. The CH/PANI hybrid follows the pseudo second‐order adsorption kinetics and Temkin isotherm model for the adsorption of both AG and MB dyes. This assumes that the enthalpy of dyes molecules decreases with the adsorption on heterogeneous surface with various kinds of adsorption sites and as…

ABSTRACT By use of biaxial stretching process of poly(vinylidene fluoride) fabrication to gain high piezoelectricity is the focus in this article. The influence of different stretch ratio and temperature are investigated and compared to uniaxial stretching process. The Fourier transform infrared spectroscopy and X‐ray diffraction are used to observe the β‐phase fraction and the degree of crystallinity. The piezoelectric coefficients (d33, d31) and the sensitivity are also measured. All the above characteristic examinations show the same consequences that equi‐biaxial stretching process employed with same stretch ratio in both axial directions of poly(vinylidene fluoride) fabrication is the focus in this article. And heating temperature would have adequate piezoelectricity approximate to uniaxial stretching. In observation of surface morphology by using scanning electron microscopy, uniformity in biaxial direction is gained. However, biaxial stretching with higher stretch ratio of R = 4 × 4 would produce porosity and crack. Via atomic force microscopy, biaxial stretching with higher…

ABSTRACT Commercial epoxy sized carbon fibers (CFs) or unsized CFs have poor interfacial adhesion with polyamide 6 (PA6). Here, CFs are coated with polyurethane (PU) and their surface properties in terms of surface chemistry, contact angle, roughness, and morphology, are investigated. The results of Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy demonstrate PU sizing evidently increases the quantity of polar functional groups on the CFs surface. The surface energy of the PU sized fiber is calculated according to the Owens–Wendt method. Compared with unsized fibers, the contact angle of PU sized fibers is decreased while their total surface energy is increased, indicating superior wettability. Moreover, transverse fiber bundle tests are performed to determine the interfacial adhesion between the CFs and PA6 matrix. The transverse fiber bundle strength of unsized CF is measured to be 12.57 MPa. For PU sized CFs processed with sizing concentration of 1.2%, this value is increased to 24.35 MPa, showing…

ABSTRACT In this study, we synthesized novel films based on bacterial cellulose (BC), BC modified by polypyrrole (PPy), and a PPy–zinc oxide nanocomposite (BC–PPy–ZnO). The soft polymerization method at room temperature was used to obtain the BC–PPy and BC–PPy–ZnO films. The Combined D‐Optimal design was used to study the effects of the pyrrole monomer concentration, ZnO concentration, and polymerization time on the morphological, physical, color, and electrical conductivity properties of the films. Fourier transform infrared results reflected that some new interactions occurred between BC and PPy and PPy–ZnO. The X‐ray diffraction analysis showed that the crystalline behavior of the BC fiber was hindered because of the complete coating with the amorphous PPy particles. Scanning electron microscopy results show that the ZnO, PPy, and PPy–ZnO nanoparticles were placed between the BC fibers. PPy decreased the water vapor permittivity and total soluble matter percentage. Electrical conductivity studies of the synthesized BC–PPy–ZnO film showed that the film's electrical resistance was…

ABSTRACT Three‐dimensional (3D) printing processes are nowadays leading the charge in transforming traditional art, engineering, and manufacturing processes. In this study, the structural and thermal behavior of commercially available filaments composed of synthetic poly(acrylonitrile‐ co ‐butadiene‐ co ‐styrene) thermoplastic as well as poly(lactic acid) and poly(lactic acid)/polyhydroxyalcanoate reinforced with bamboo ( Bambusa sp .) wood flour composite biothermoplastics were assessed by differential scanning calorimetry and infrared spectroscopy, aiming to understand the modifications that occur at the molecular level during their 3D printing. It has been determined that the biothermoplastic materials undergo both molecular reorientations related to tacticity increase and crystallinity decrease when submitted to 3D printing extrusion, while the synthetic thermoplastic undergoes crosslinking due to its butadiene component. All of the studied materials present good water stability (with water uptake values between 0.8% and 24%), and the water absorption follows a pseudo‐Fickian…

ABSTRACT In this work, a bio‐based flame retardant, casein, was incorporated into poly(lactic acid) (PLA) matrix by melt compounding in order to improve the fire resistance and sustain the biodegradable character of PLA simultaneously. The fire performance of PLA composites was evaluated by limiting oxygen index, UL‐94 vertical burning, and cone calorimeter tests, respectively. The results indicated that the introduction of 20% casein increased the limiting oxygen index value of PLA composites from 20.0% to 32.2%, upgraded the UL‐94 rating from no rating to V‐0, and decreased the peak heat release rate from 779 to 639 kW/m2. The decomposition products of PLA composites were analyzed by Fourier transform infrared, and the morphology of the char after combustion was observed by scanning electron microscopy. It was suggested that casein took effects in both gas phase by releasing non‐flammable gases (such as NH3 and H2O) and condensed phase by the formation of protective char layers. However, the presence of casein in PLA induced an unavoidable deterioration in the mechanical…

ABSTRACT In this article, the performance of polyethersulfone (PES) ultra‐ and nanofiltration membranes, prepared with the non‐toxic solvent dimethyl sulfoxide (DMSO), was investigated. The membranes were prepared by immersion precipitation via phase inversion. Experimental results proved that DMSO is a better alternative to N‐methyl‐2‐pyrrolidone (NMP) as solvent for PES ultrafiltration membranes as the membranes had a higher permeability and rejection of bovine serum albumin (BSA). An explanation was found based on experimental cloud point data and scanning electron microscopy images showing the morphology. The rejection of BSA and rose Bengal (RB) was proportional to the polymer concentration. On the contrary, the permeability decreased with increasing polymer concentration. For a casting thickness of 250 µm, an optimal balance between permeability and rejection of macromolecules for ultrafiltration was found at 24 wt % PES. The permeability was inversely proportional to the casting thickness, but a small decrease in rejection was observed when lowering the thickness. A good…

ABSTRACT Separator is a very important set of lithium‐ion batteries. At present, low porosity and poor thermal stability are two major disadvantages of separator. In this work, we first apply electrospinning method to prepare the Polytetrafluoroethylene (PTFE) nanofiber separator, which has the advantages of electrospinning method and PTFE materials. The effect of the PTFE nanofiber separator is investigated by scanning electron microscope, Capillary Flow Porometer, thermogravimetric–differential scanning calorimeter, linear sweep voltammeter, AC impedance, and charge/discharge cycling tests. The results demonstrate that the PTFE nanofiber separator has a special fiber structure made from PTFE particles gathering one by one along the fibers. Moreover, the PTFE nanofiber separator exhibits several advantages, including suitable pore diameter, uniform pore size distribution, high porosity, and electrolyte uptake, which enhance the ionic conductivity. The thermal stability of the PTFE nanofiber separator is much better than that of the conventional polyolefin separator. The Li/LiCoO2…

ABSTRACT In this work, a new type of environment‐friendly solidified dust suppressant was developed to solve the dust pollution problem in open pit coalmines, coal bunkers, and so on. Natural polymer chitosan with excellent properties was chemically modified. Infrared spectroscopy was adopted to characterize the product. Using substitution rate as the evaluating indicator, the optimized mass ratio between monomer 3‐chloro‐2‐hydroxypropyl trimethyl ammonium chloride and chitosan, reaction temperature, reaction time, and pH were determined via single factor experiments. Combining the results of the four‐factor‐four‐level orthogonal experiment, the optimum reaction conditions A2B3C4D3 were obtained. The hardened film on the surface of coal powders was observed by high‐resolution scanning electron microscope. In addition, the water retention, solidification performance, and wind erosion resistance of the dust suppressant, as well as its influence on coal properties were measured. The results show that the synthesized dust suppressant demonstrates excellent properties and has good dust…

ABSTRACT In the present work, poly(vinyl alcohol)/ Syzygium cumini leaves extract (PSN) and poly(vinyl alcohol)/chitosan/ S. cumini leaves extract blend films were prepared by solution casting technique. The films were characterized by using scanning electron microscopy, atomic force microscopy, X‐ray diffraction study, Fourier transform infrared spectroscopy, thermogravimetric analysis, and universal testing machine. The results indicated that the appreciable physical interaction at lower concentrations of S. cumini leaves extract in the PVA and PVA/chitosan films contribute to the smooth uniform morphology, increased the degree of crystallinity, degradation temperature, and improved mechanical properties. Further, films were analyzed with water contact angle analyzer which illustrates that blend films were hydrophilic (PSN‐1) and hydrophobic (PCS‐1) in nature. However, blend films were also subjected to the antimicrobial study, which revealed that inclusion of S. cumini leaves extracts significantly enhanced the antibacterial activity in the PVA and PVA/chitosan film. With all of…

In recent decades, nanoparticles have shown significant promise as an oncology treatment modality. Responsive polymers represent a promising class of nanoparticles that can trigger delivery through the exploitation of a specific stimuli. Response to a stimulus is one of the most basic processes found in living systems. As such, the desire to engineer dynamic and functional materials is becoming more prevalent in an effort to achieve precise control over our environment. The combination of controlled radical polymerization and high yielding chemistry strategies provide an excellent basis for the development of the next generation of drug delivery systems. The versatility of polymer chemistries available enables the synthesis of increasingly complex architectures with enhanced delivery specificity and control over the desired properties to interface with biological systems. This tutorial review highlights recent developments in polymer-based approaches to internally responsive nanoparticles for oncology. Presented are concise overviews of the current challenges and opportunities in…

ABSTRACT A three‐layer functional coating was prepared through layer‐by‐layer (LbL) assembly and a sol–gel process. The multilayered coating was composed of a phytic acid (PA) coating dipped between two layers of flexible polysiloxane coatings and was deposited on the polyester fabric by LbL assembly. Flammability tests indicated that the multilayer coating prevented droplet generation during combustion. The PA also absorbed the reactive free radicals to reduce the flame‐burning rate. After being soaked for only 20 min in PA solution, the fabric exhibited self‐extinguishing properties and antidroplet effect during the vertical flame test, while cone calorimetry confirmed that the coated fabric exhibited a 65% decrease in the peak heat release rate and reduced the total amount of smoke released by 72%. After washing the coated fabric 45 times, there was no significant decrease in the phosphorus content and the limiting oxygen index of coated fabrics. Thus, the coating synthesized in this study is an effective method of constructing durable, functional coatings on the surface of…

ABSTRACT Polyurethane foams are in general flammable and their flammability can be controlled by adding flame‐retardant (FR) materials. Reactive FR have the advantage of making strong bond within the polyurethane chains to provide excellent FR over time without compromising physico‐mechanical properties. Here, phenyl phosphonic acid and propylene oxide‐based reactive FR polyol was synthesized and used along with limonene based polyol for preparation of FR polyurethanes. All the obtained foams showed higher closed cell content (above 96%). By the addition of FR–polyol, the compressive strength of the foams showed 160% increment which could be due to reactive nature of FR–polyol. Moreover, 1.5 wt % of phosphorus (P) content reduced the self‐extinguishing time of the foam from 81 (28% weight loss) to 11.2 s (weight loss of 9.8%). Cone test showed 68.6% reduction in peak heat release rate along with 23.4% reduction in thermal heat release. The change in char structure of carbon after burning was analyzed using Raman spectra which, suggests increment in the graphitic phase of the carbon…

ABSTRACT A series of thermoplastic polyurethane (TPU)/poly(lactic acid) (PLA) blends are studied in terms of morphological, thermal, and rheological properties by scanning electron microscopy, differential scanning calorimetry, and rheometry. Using supercritical CO2 batch foaming, the foamability of the blends is systematically investigated. It is found that the 80/20 (wt %/wt %) TPU/PLA blend (TPU80%) shows vastly enhanced foamability over a wide range of foaming conditions to produce foams with a myriad of cellular morphology. The foamability enhancement results from the improved cell nucleation and growth, and the changes in the polymer microstructure. Compared to elastic TPU foams, the TPU80% retain their shapes 3.4 times better. Mechanism for the enhanced stability is proposed and verified using Kohlrausch–Williams–Watts model. The materials developed in the study and the mechanistic understanding of the shape fixation process may facilitate the advancement of elastomeric foams in conventional use as well as in novel shape memory applications. © 2018 Wiley Periodicals, Inc. J.…

ABSTRACT Superior conductive fillers reinforced polymer composites are ideal alternatives to graphitic and metallic materials in proton exchange membrane fuel cells (PEMFCs) for high thermal and electrical conductive bipolar plates. Polymer composites are known to be adversely influenced from high contact resistance thus to minimize such resistance, highly graphite‐/graphene‐filled polybenzoxazine (PBA) composites are developed in this work. A very low melt viscosity of benzoxazine resin with graphite loading as high as 83 wt % is used for the samples. With an addition of graphene platelet, thermal and electrical conductivities of the specimens having 75.5 wt % of graphite in a combination of 7.5 wt % of graphene are significantly enhanced to 14.5 W mK−1 and 323 S cm−1, respectively. Properties of highly graphite‐/graphene‐filled PBA composites exhibit most values exceed those requirements by the U.S. Department of Energy for PEMFCs applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47183.

ABSTRACT Simple, direct precipitation was used to synthesize green, renewable, biobased flame retardants. Copper phytate (Cu–Phyt), zinc phytate, aluminum phytate, and tin phytate (Sn–Phyt) were synthesized. Thermogravimetric analysis performed in N2 revealed that the metallic phytate (M–Phyt, where M is Cu, Zn, Al, or Sn) salts showed good charring. The limiting oxygen index (LOI), cone calorimetry (CONE) test data, tensile strength, and impact toughness were measured for flexible poly(vinyl chloride) (PVC) containing 15 wt % M–Phyt salts. The PVC/Sn–Phyt LOI rose from 24.9 to 30.3%, and the PVC/Sn–Phyt mechanical properties were on par with those of the pure PVC. The CONE test results indicate that PVC/Cu–Phyt showed the lowest total smoke production (TSP) and peak heat‐release rate (pHRR) among the samples. The TSP and pHRR of PVC/Cu–Phyt were 15.77 m2 and 181.77 kW/m2, respectively, 62.63 and 44.48% lower than those of the neat PVC. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46601.

ABSTRACT We demonstrate that the catalyst Perkalite F100 efficiently works as a nanocatalyst in the depolymerization of poly(ethylene terephthalate) (PET). After depolymerization of PET in the presence of ethylene glycol and the Perkalite nanocatalyst, the main product obtained was bis(2‐hydroxylethyl) terephthalate (BHET) with high purity, as confirmed by Fourier transform infrared spectroscopy and NMR. The BHET monomers could serve directly as starting materials in a further polymerization into PET with a virgin quality and contribute to a solution for the disposal of PET polymers. Compared with the direct glycolysis of PET, the addition of a predegradation step was shown to reduce the reaction time needed to reach the depolymerization equilibrium. The addition of the predegradation step also allowed lower reaction temperatures. Therefore, the strategy to include a predegradation step before depolymerization is suitable for increasing the efficiency of the glycolysis reaction of PET into BHET monomers. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46285.

ABSTRACT The growth in polymer‐based innovative packaging technology has brought about a revolution in extending the shelf life of many food and aquatic products. One of the emerging areas in this field is polymer nanocomposite (PNC) technology, which involves the incorporation of various chemicals and nanoadditives into polymers to improve their inherent properties or to add required functionality. Because the nanoparticles may interact with food components during processing, storage, or distribution and may migrate into food, PNC‐based packaging materials require awareness and understanding of their potential impact on human health and the environment. Interest in migration and cytotoxic analysis of PNC has gained considerable momentum in recent years. The focus of this article is on clay‐containing PNCs because the global trend in PNCs shows that 50% of all nanofillers constitute nanoclays of either natural or synthetic origin. This article presents a summary of perspectives on international regulations on test parameters and migration of chemicals from materials that come into…

ABSTRACT Bioactive wound dressings from poly(vinyl alcohol) (PVA) and zein nanoparticles (NPs) loaded with diclofenac (DLF) were prepared successfully by the single jet electrospinning method. DLF‐loaded zein NPs with an average diameter of ∼228 nm were prepared using anti‐solvent precipitation method. The formulation of zein:DLF 1:1 exhibited optimum encapsulation efficiency of 47.80%. The NPs were characterized by dynamic light scattering, zeta‐potential measurement, and differential scanning calorimetry. In vitro, drug release profiles of the DLF‐loaded zein NPs, and PVA–zein NPs were also studied within 120 h and showed the release efficiency of nearly 80% from zein NPs. A more controlled release of DLF was achieved by embedding the zein NPs in the PVA nanofibers. Fourier transform infrared spectroscopy was used to analyze possible interactions between different components of the fabricated dressings. The mechanical properties of the developed dressings were also evaluated using uniaxial tensile testing. Young's modulus ( E ) of the dressings decreased after inclusion of zein…

ABSTRACT Currently, the most widely used binder in batteries is polyvinylidene fluoride with N‐methyl‐2‐pyrrolidone used as a solvent. This solvent is flammable and toxic. Here, we focus on the suitability of using water‐soluble sodium alginate (Na‐alginate) and sodium carboxymethyl cellulose (Na‐CMC) as alternative biobased binder materials for the anodes of lithium ion batteries. It reduces the environmental impact of current manufacturing processes. However, control of the rheological characteristics of the binder whilst containing active and conductive additives is key for optimized processing. Here, we perform stability and rheological measurements of Na‐alginate and Na‐CMC solutions containing varying amounts of graphite and carbon black used as active and conductive materials, respectively. Compared with the benchmark Na‐CMC, the degree of flocculation shows that for the same concentration of binder in water, Na‐alginate suspensions are more stable. The rheology measurements show that Na‐alginate slurries have a higher viscosity than Na‐CMC at a shear rate of 50 s−1 with that…

Abstract In this study, we investigated different proportions of alginate and carboxymethyl cellulose (CMC) biopolymers in the formulation of films to act as wound dressings. With the casting method, monolayer and bilayer (BL) films were produced with alginate/CMC proportions (weight percentages) of 0:100 (0A), 25:75 (25A), 50:50 (50A), 75:25 (75A), and 100:0 (100A). Thin, homogeneous, and continuous films were obtained with glycerol and crosslinking with CaCl2. The fluid uptake, film stability, and morphological, mechanical, thermal, and barrier properties were evaluated. A general tendency of the film characteristics was visualized: 50A had intermediary characteristics from both polymers; although the liquid behavior characteristics were improved with increasing CMC content, the mechanical properties worsened. When compared to the monolayer film (50A), the BL film 50A–BL demonstrated a better water vapor transmission rate. In this study, we demonstrated the necessity of varying the polymer concentrations to assist in the production of wound dressings. © 2018 Wiley Periodicals,…

ABSTRACT The non‐isothermal crystallization behaviors of PA56, PA66, and PA56/PA66 blends were studied by differential scanning calorimetry. The Jeziorny and Mo's methods were used to analyze their non‐isothermal crystallization kinetics. The results indicated that Mo's method was better to describe the experimental data in this work. The crystallization rate of PA56 was much slower than that of PA66. The crystallization rate of PA56/PA66 blend was speeded up significantly with the increasing PA66 content when the PA66 content was less than 30 wt %. Further increase in the PA66 content only leads to relatively less increase of the crystallization rate in the PA56/PA66 blends. Activation energies have been determined with Friedman method. The activation energy of PA56/PA66 blends is decreased and lower than that of PA56. PA66 may play a role of nucleating agent toward PA56 to make it crystallize more easily in PA56/PA66 blends. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46409.

ABSTRACT In the present study, graphene oxide (GO) was incorporated into poly(vinylidene fluoride) (PVDF) and chemically modified PVDF (M‐PVDF) to prepare mixed matrix membranes (MMMs) for gas separation application. Performed analyses proved appropriate dispersion of exfoliated GO sheets in polymer matrices and sufficient compatibility at the interfacial phases. M‐PVDF based MMMs were thermally and mechanically more stable relative to the PVDF‐based MMMs. The oxygen containing functional groups in M‐PVDF was probably the main reason for this more stability. PVDF/GO MMMs rendered low gas permeability and high selectivity. Both impermeable GO sheets and crystalline phases of PVDF were responsible for such behavior. On the other hand, interestingly gas permeability of M‐PVDF/GO MMMs was enhanced while no substantial decline was recorded in gas selectivity. For instance, He and CO2 permeability was increased 12.46% and 25.89%, respectively, compared to the pure PVDF membrane. This behavior originated from functional groups of M‐PVDF and the interaction of these groups with GO sheets.…

ABSTRACT A series of polyvinyl alcohol (PVA)/graphene oxide (GO)‐sodium alginate (SA) nanocomposite hydrogel beads were prepared through in situ crosslinking for Pb2+ removal. It was found that PVA and SA molecules were intercalated into GO layers through hydrogen bonding interactions, leading to the destruction of orderly structure of GO, while GO uniformly distributed in PVA matrix. With increasing PVA solution concentration, the hydrogel beads became more regular, a large number of polygonal pores with thin walls and open pores formed, the average pore size decreased, and the dense network structure formed. Meanwhile, the permeability of the composite hydrogel decreased, leading to the decline of Pb2+ adsorption capacity of the composite hydrogel. With increasing GO content, the ballability of the hydrogel beads was weakened, the pore size increased, and relatively loose network structure formed, resulting in an increase in permeability and Pb2+ adsorption capacity of the hydrogel, reaching up to 279.43 mg g−1. Moreover, the composite hydrogel presented relatively good…

ABSTRACT This article describes the adsorption and tensile behavior of electrospun polyacrylonitrile (PAN) nanofiber mats loaded with different amounts of ZnO [0.5, 1.0, 2.0, and 5.0 wt%] nanoparticles. X‐ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transforminfrared (FTIR) spectroscopy, and thermal gravimetric analysis (TGA) were utilized to characterize the resulting composite nanofibers. Microscopic investigations revealed that the increase in surface roughness and diameter of the electrospun PAN nanofibers was due to the addition of ZnO nanoparticles. Adsorption results indicated that the fabricated PAN/ZnO (2.0 wt%) composite nanofiber mats showed the best adsorption performance with 261% and 167% increase in adsorption capacities for Pb(II) and Cd(II) from aqueous solutions, respectively, compared to pristine PAN nanofibers. The adsorption equilibrium was reached within 60 min, and the process could be described using the nonlinear pseudo‐second‐order kinetic model. The adsorption isotherm study was better represented by the Langmuir model, which…

ABSTRACT Polyetheramine (PEA)‐modified epoxies with various types of PEAs were prepared and respective effects on characteristics of epoxy networks were studied. The used PEAs were polyethylene glycol diamine (PEG‐amine) and polypropylene glycol diamine (PPG‐amine) with two different molecular weights (i.e., 200 and 400 g mol−1). According to mechanical tests, the structural parameters of PEAs played an important role in final properties of epoxy/amine systems. PEG400‐amine and PPG200‐amine had the highest and lowest effects on the properties of epoxy networks, respectively. Whereas 10 phr PEG400‐amine increased critical stress intensity factor (KIC) and critical strain energy release rate (GIC) of the epoxy up to 82 and 294%, the same number of PPG200‐amine chains caused to increase the KIC and GIC up to 11 and 34%. This discrepancy could be assigned to higher flexibility index (φ = 26.22), longer chain length (~27 atoms), and higher secondary interactions [δ = 9.69 (cal cm−3)0.5] of PEG400‐amine in comparison with PPG200‐amine [with φ = 8.08, ~10 atoms in chain, and δ = 8.98 (cal…

ABSTRACT A new membrane was synthesized containing pure alginate, crosslinking agent (CaCl2), and plasticizer (glycerol). Characterization studies of the membrane were applied to determine the characteristics and morphology using field emission scanning electron microscope, EDX, FTIR, XRD, and atomic force microscopy analysis. The half‐cell performance test of the membrane was verified by several tests, including proton conductivity and methanol permeability. The best membrane had high proton conductivity (10.1 × 10−3 S cm−1) and very low methanol permeability (1.984 × 10−7 cm2 s−1), which consequently resulted in very high selectivity (5.0907 × 104 Ss cm−3). Glycerol had a positive modification and good influence on the alginate characteristics. Furthermore, the poor mechanical properties of the alginate biopolymer were enhanced by calcium chloride and glycerol inside the polymer. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46666.

ABSTRACT This study investigated a simple synthesis of a crosslinked poly(vinyl alcohol)/ graphene oxide composite membrane with lower ethanol permeability membrane for passive direct ethanol–proton exchange membrane fuel cells (DE‐PEMFCs). The chemical and physical structure, morphologies, ethanol uptake and permeability, ion exchange capacities, water uptake, and proton conductivities were determined and found that transport properties of the membrane were affected by the GO loading. The composite membrane with optimum GO content (15 wt %) exhibited the highest proton conductivity of 9.5 × 10−3 Scm−1 at 30°C, 3.24 × 10−2 Scm−1 at 60°C, respectively and reduced ethanol permeability until 1.75 × 10−7 cm2 s−1. In the passive DE‐PEMFC, the power density at 60°C were obtained as 5.84 mW cm−2 higher than those by commercial Nafion 117 is 4.52 mW cm−2. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 46928.