The 50 most-cited articles in Advanced Materials, 2018

Over the past 30 years, significant commercial and academic progress has been made on Li-based battery technologies. From the early Li-metal anode iterations to the current commercial Li-ion batteries (LIBs), the story of the Li-based battery is full of breakthroughs and back tracing steps. This review will discuss the main roles of material science in the development of LIBs. As LIB research progresses and the materials of interest change, different emphases on the different subdisciplines of material science are placed. Early works on LIBs focus more on solid state physics whereas near the end of the 20th century, researchers began to focus more on the morphological aspects (surface coating, porosity, size, and shape) of electrode materials. While it is easy to point out which specific cathode and anode materials are currently good candidates for the next-generation of batteries, it is difficult to explain exactly why those are chosen. In this review, for the reader a complete developmental story of LIB should be clearly drawn, along with an explanation of the reasons responsible…

Metal-organic frameworks (MOFs) are an emerging class of porous materials with potential applications in gas storage, separations, catalysis, and chemical sensing. Despite numerous advantages, applications of many MOFs are ultimately limited by their stability under harsh conditions. Herein, the recent advances in the field of stable MOFs, covering the fundamental mechanisms of MOF stability, design, and synthesis of stable MOF architectures, and their latest applications are reviewed. First, key factors that affect MOF stability under certain chemical environments are introduced to guide the design of robust structures. This is followed by a short review of synthetic strategies of stable MOFs including modulated synthesis and postsynthetic modifications. Based on the fundamentals of MOF stability, stable MOFs are classified into two categories: high-valency metal-carboxylate frameworks and low-valency metal-azolate frameworks. Along this line, some representative stable MOFs are introduced, their structures are described, and their properties are briefly discussed. The expanded…

Advances in soft robotics, materials science, and stretchable electronics have enabled rapid progress in soft grippers. Here, a critical overview of soft robotic grippers is presented, covering different material sets, physical principles, and device architectures. Soft gripping can be categorized into three technologies, enabling grasping by: a) actuation, b) controlled stiffness, and c) controlled adhesion. A comprehensive review of each type is presented. Compared to rigid grippers, end-effectors fabricated from flexible and soft components can often grasp or manipulate a larger variety of objects. Such grippers are an example of morphological computation, where control complexity is greatly reduced by material softness and mechanical compliance. Advanced materials and soft components, in particular silicone elastomers, shape memory materials, and active polymers and gels, are increasingly investigated for the design of lighter, simpler, and more universal grippers, using the inherent functionality of the materials. Embedding stretchable distributed sensors in or on soft grippers…

Nanoparticle-based therapeutic, prevention, and detection modalities have the potential to greatly impact how diseases are diagnosed and managed in the clinic. With the wide range of nanomaterials available, the rational design of nanocarriers on an application-specific basis has become increasingly commonplace. Here, a comprehensive overview is provided on an emerging platform: cell-membrane-coating nanotechnology. As a fundamental unit of biology, cells carry out a wide range of functions, including the remarkable ability to interface and interact with their surrounding environment. Instead of attempting to replicate such functions via synthetic techniques, researchers are now directly leveraging naturally derived cell membranes as a means of bestowing nanoparticles with enhanced biointerfacing capabilities. This top-down technique is facile, highly generalizable, and has the potential to greatly augment existing nanocarriers. Further, the introduction of a natural membrane substrate onto nanoparticles surfaces has enabled additional applications beyond those traditionally…

Abstract Ever‐increasing fossil‐fuel combustion along with massive CO 2 emissions has aroused a global energy crisis and climate change. Photocatalytic CO 2 reduction represents a promising strategy for clean, cost‐effective, and environmentally friendly conversion of CO 2 into hydrocarbon fuels by utilizing solar energy. This strategy combines the reductive half‐reaction of CO 2 conversion with an oxidative half reaction, e.g., H 2 O oxidation, to create a carbon‐neutral cycle, presenting a viable solution to global energy and environmental problems. There are three pivotal processes in photocatalytic CO 2 conversion: (i) solar‐light absorption, (ii) charge separation/migration, and (iii) catalytic CO 2 reduction and H 2 O oxidation. While significant progress is made in optimizing the first two processes, much less research is conducted toward enhancing the efficiency of the third step, which requires the presence of cocatalysts. In general, cocatalysts play four important roles: (i) boosting charge separation/transfer, (ii) improving the activity and selectivity of CO 2…

Abstract Rechargeable lithium‐metal batteries (LMBs) are regarded as the “holy grail” of energy‐storage systems, but the electrolytes that are highly stable with both a lithium‐metal anode and high‐voltage cathodes still remain a great challenge. Here a novel “localized high‐concentration electrolyte” (HCE; 1.2 m lithium bis(fluorosulfonyl)imide in a mixture of dimethyl carbonate/bis(2,2,2‐trifluoroethyl) ether (1:2 by mol)) is reported that enables dendrite‐free cycling of lithium‐metal anodes with high Coulombic efficiency (99.5%) and excellent capacity retention (>80% after 700 cycles) of Li||LiNi1/3Mn1/3Co1/3O2 batteries. Unlike the HCEs reported before, the electrolyte reported in this work exhibits low concentration, low cost, low viscosity, improved conductivity, and good wettability that make LMBs closer to practical applications. The fundamental concept of “localized HCEs” developed in this work can also be applied to other battery systems, sensors, supercapacitors, and other electrochemical systems.

2D transition metal carbides, carbonitrides, and nitrides, known as MXenes, are a rapidly growing family of 2D materials with close to 30 members experimentally synthesized, and dozens more studied theoretically. They exhibit outstanding electronic, optical, mechanical, and thermal properties with versatile transition metal and surface chemistries. They have shown promise in many applications, such as energy storage, electromagnetic interference shielding, transparent electrodes, sensors, catalysis, photothermal therapy, etc. The high electronic conductivity and wide range of optical absorption properties of MXenes are the key to their success in the aforementioned applications. However, relatively little is currently known about their fundamental electronic and optical properties, limiting their use to their full potential. Here, MXenes' electronic and optical properties from both theoretical and experimental perspectives, as well as applications related to those properties, are discussed, providing a guide for researchers who are exploring those properties of MXenes.

Separation is an important industrial step with critical roles in the chemical, petrochemical, pharmaceutical, and nuclear industries, as well as in many other fields. Although much progress has been made, the development of better separation technologies, especially through the discovery of high-performance separation materials, continues to attract increasing interest due to concerns over factors such as efficiency, health and environmental impacts, and the cost of existing methods. Metal-organic frameworks (MOFs), a rapidly expanding family of crystalline porous materials, have shown great promise to address various separation challenges due to their well-defined pore size and unprecedented tunability in both composition and pore geometry. In the past decade, extensive research is performed on applications of MOF materials, including separation and capture of many gases and vapors, and liquid-phase separation involving both liquid mixtures and solutions. MOFs also bring new opportunities in enantioselective separation and are amenable to morphological control such as fabrication…

Flexible and wearable electronics are attracting wide attention due to their potential applications in wearable human health monitoring and care systems. Carbon materials have combined superiorities such as good electrical conductivity, intrinsic and structural flexibility, light weight, high chemical and thermal stability, ease of chemical functionalization, as well as potential mass production, enabling them to be promising candidate materials for flexible and wearable electronics. Consequently, great efforts are devoted to the controlled fabrication of carbon materials with rationally designed structures for applications in next-generation electronics. Herein, the latest advances in the rational design and controlled fabrication of carbon materials toward applications in flexible and wearable electronics are reviewed. Various carbon materials (carbon nanotubes, graphene, natural-biomaterial-derived carbon, etc.) with controlled micro/nanostructures and designed macroscopic morphologies for high-performance flexible electronics are introduced. The fabrication strategies, working…

All-solid-state lithium batteries (ASSLBs) have the potential to revolutionize battery systems for electric vehicles due to their benefits in safety, energy density, packaging, and operable temperature range. As the key component in ASSLBs, inorganic lithium-ion-based solid-state electrolytes (SSEs) have attracted great interest, and advances in SSEs are vital to deliver the promise of ASSLBs. Herein, a survey of emerging SSEs is presented, and ion-transport mechanisms are briefly discussed. Techniques for increasing the ionic conductivity of SSEs, including substitution and mechanical strain treatment, are highlighted. Recent advances in various classes of SSEs enabled by different preparation methods are described. Then, the issues of chemical stabilities, electrochemical compatibility, and the interfaces between electrodes and SSEs are focused on. A variety of research addressing these issues is outlined accordingly. Given their importance for next-generation battery systems and transportation style, a perspective on the current challenges and opportunities is provided, and…

Abstract New lithium halide solid‐electrolyte materials, Li 3 YCl 6 and Li 3 YBr 6 , are found to exhibit high lithium‐ion conductivity, high deformability, and high chemical and electrochemical stability, which are required properties for all‐solid‐state battery (ASSB) applications, particularly for large‐scale deployment. The lithium‐ion conductivities of cold‐pressed powders surpass 1 mS cm −1 at room temperature without additional intergrain or grain boundary resistances. Bulk‐type ASSB cells employing these new halide solid electrolyte materials exhibit coulombic efficiencies as high as 94% with an active cathode material of LiCoO 2 without any extra coating. These superior electrochemical characteristics, as well as their material stability, indicate that lithium halide salts are another promising candidate for ASSB solid electrolytes in addition to sulfides or oxides.

Abstract Fluorine‐contained polymers, which have been widely used in highly efficient polymer solar cells (PSCs), are rather costly due to their complicated synthesis and low yields in the preparation of components. Here, the feasibility of replacing the critical fluorine substituents in high‐performance photovoltaic polymer donors with chlorine is demonstrated, and two polymeric donors, PBDB‐T‐2F and PBDB‐T‐2Cl, are synthesized and compared in parallel. The synthesis of PBDB‐T‐2Cl is much simpler than that of PBDB‐T‐2F. The two polymers have very similar optoelectronic and morphological properties, except the chlorinated polymer possess lower molecular energy levels than the fluorinated one. As a result, the PBDB‐T‐2Cl‐based PSCs exhibit higher open circuit voltage ( V oc ) than the PBDB‐T‐2F‐based devices, leading to an outstanding power conversion efficiency of over 14%. This work establishes a more economical design paradigm of replacing fluorine with chlorine for preparing highly efficient polymer donors.

Collagen is the oldest and most abundant extracellular matrix protein that has found many applications in food, cosmetic, pharmaceutical, and biomedical industries. First, an overview of the family of collagens and their respective structures, conformation, and biosynthesis is provided. The advances and shortfalls of various collagen preparations (e.g., mammalian/marine extracted collagen, cell-produced collagens, recombinant collagens, and collagen-like peptides) and crosslinking technologies (e.g., chemical, physical, and biological) are then critically discussed. Subsequently, an array of structural, thermal, mechanical, biochemical, and biological assays is examined, which are developed to analyze and characterize collagenous structures. Lastly, a comprehensive review is provided on how advances in engineering, chemistry, and biology have enabled the development of bioactive, 3D structures (e.g., tissue grafts, biomaterials, cell-assembled tissue equivalents) that closely imitate native supramolecular assemblies and have the capacity to deliver in a localized and sustained…

Abstract An electronic (e‐) skin is expected to experience significant wear and tear over time. Therefore, self‐healing stretchable materials that are simultaneously soft and with high fracture energy, that is high tolerance of damage or small cracks without propagating, are essential requirements for the realization of robust e‐skin. However, previously reported elastomers and especially self‐healing polymers are mostly viscoelastic and lack high mechanical toughness. Here, a new class of polymeric material crosslinked through rationally designed multistrength hydrogen bonding interactions is reported. The resultant supramolecular network in polymer film realizes exceptional mechanical properties such as notch‐insensitive high stretchability (1200%), high toughness of 12 000 J m−2, and autonomous self‐healing even in artificial sweat. The tough self‐healing materials enable the wafer‐scale fabrication of robust and stretchable self‐healing e‐skin devices, which will provide new directions for future soft robotics and skin prosthetics.

Abstract Due to the Fenton reaction, the presence of Fe and peroxide in electrodes generates free radicals causing serious degradation of the organic ionomer and the membrane. Pt‐free and Fe‐free cathode catalysts therefore are urgently needed for durable and inexpensive proton exchange membrane fuel cells (PEMFCs). Herein, a high‐performance nitrogen‐coordinated single Co atom catalyst is derived from Co‐doped metal‐organic frameworks (MOFs) through a one‐step thermal activation. Aberration‐corrected electron microscopy combined with X‐ray absorption spectroscopy virtually verifies the CoN 4 coordination at an atomic level in the catalysts. Through investigating effects of Co doping contents and thermal activation temperature, an atomically Co site dispersed catalyst with optimal chemical and structural properties has achieved respectable activity and stability for the oxygen reduction reaction (ORR) in challenging acidic media (e.g., half‐wave potential of 0.80 V vs reversible hydrogen electrode (RHE). The performance is comparable to Fe‐based catalysts and 60 mV lower than Pt/C…

Abstract Isolated single atomic site catalysts have attracted great interest due to their remarkable catalytic properties. Because of their high surface energy, single atoms are highly mobile and tend to form aggregate during synthetic and catalytic processes. Therefore, it is a significant challenge to fabricate isolated single atomic site catalysts with good stability. Herein, a gentle method to stabilize single atomic site metal by constructing defects on the surface of supports is presented. As a proof of concept, single atomic site Au supported on defective TiO 2 nanosheets is prepared and it is discovered that (1) the surface defects on TiO 2 nanosheets can effectively stabilize Au single atomic sites through forming the Ti–Au–Ti structure; and (2) the Ti–Au–Ti structure can also promote the catalytic properties through reducing the energy barrier and relieving the competitive adsorption on isolated Au atomic sites. It is believed that this work paves a way to design stable and active single atomic site catalysts on oxide supports.

As a new generation of artificial enzymes, nanozymes have the advantages of high catalytic activity, good stability, low cost, and other unique properties of nanomaterials. Due to their wide range of potential applications, they have become an emerging field bridging nanotechnology and biology, attracting researchers in various fields to design and synthesize highly catalytically active nanozymes. However, the thorough understanding of experimental phenomena and the mechanisms beneath practical applications of nanozymes limits their rapid development. Herein, the progress of experimental and computational research of nanozymes on two issues over the past decade is briefly reviewed: (1) experimental development of new nanozymes mimicking different types of enzymes. This covers their structures and applications ranging from biosensing and bioimaging to therapeutics and environmental protection. (2) The catalytic mechanism proposed by experimental and theoretical study. The challenges and future directions of computational research in this field are also discussed.

Nowadays, low-frequency electromagnetic interference (<2.0 GHz) remains a key core issue that plagues the effective attenuation performance of conventional absorption devices prepared via the component-morphology method (Strategy I). According to theoretical calculations, one fundamental solution is to develop a material that possesses a high ε' but lower ε″. Thus, it is attempted to control the dielectric values via applying an external electrical field, which inducts changes in the macrostructure toward a performance improvement (Strategy II). A sandwich-structured flexible electronic absorption device is designed using a carbon film electrode to conduct an external current. Simultaneously, an absorption layer that is highly responsive to an external voltage is selected via Strategy I. Relying on the synergistic effects from Strategies I and II, this device demonstrates an absorption value of more than 85% at 1.5-2.0 GHz with an applied voltage of 16 V while reducing the thickness to ≈5 mm. In addition, the device also shows a good absorption property at 25-150 °C. The method of…

Abstract The challenge in the artificial photosynthesis of fossil resources from CO 2 by utilizing solar energy is to achieve stable photocatalysts with effective CO 2 adsorption capacity and high charge‐separation efficiency. A hierarchical direct Z‐scheme system consisting of urchin‐like hematite and carbon nitride provides an enhanced photocatalytic activity of reduction of CO 2 to CO, yielding a CO evolution rate of 27.2 µmol g −1 h −1 without cocatalyst and sacrifice reagent, which is >2.2 times higher than that produced by g‐C 3 N 4 alone (10.3 µmol g −1 h −1 ). The enhanced photocatalytic activity of the Z‐scheme hybrid material can be ascribed to its unique characteristics to accelerate the reduction process, including: (i) 3D hierarchical structure of urchin‐like hematite and preferable basic sites which promotes the CO 2 adsorption, and (ii) the unique Z‐scheme feature efficiently promotes the separation of the electron–hole pairs and enhances the reducibility of electrons in the conduction band of the g‐C 3 N 4 . The origin of such an obvious advantage of the hierarchical…

Abstract A long debate on the charge identity and the associated mechanisms occurring in contact‐electrification (CE) (or triboelectrification) has persisted for many decades, while a conclusive model has not yet been reached for explaining this phenomenon known for more than 2600 years! Here, a new method is reported to quantitatively investigate real‐time charge transfer in CE via triboelectric nanogenerator as a function of temperature, which reveals that electron transfer is the dominant process for CE between two inorganic solids. A study on the surface charge density evolution with time at various high temperatures is consistent with the electron thermionic emission theory for triboelectric pairs composed of Ti–SiO 2 and Ti–Al 2 O 3 . Moreover, it is found that a potential barrier exists at the surface that prevents the charges generated by CE from flowing back to the solid where they are escaping from the surface after the contacting. This pinpoints the main reason why the charges generated in CE are readily retained by the material as electrostatic charges for hours at room…

laser on carbon materials in ambient atmosphere. This technique combines 3D graphene preparation and patterning into a single step without the need for wet chemical steps. Since its discovery in 2014, LIG has attracted broad research interest, with several papers being published per month using this approach. These serve to delineate the mechanism of the LIG-forming process and to showcase the translation into many application areas. Herein, the strategies that have been developed to synthesize LIG are summarized, including the control of LIG properties such as porosity, composition, and surface characteristics, and the advancement in methodology to convert diverse carbon precursors into LIG. Taking advantage of the LIG properties, the applications of LIG in broad fields, such as microfluidics, sensors, and electrocatalysts, are highlighted. Finally, future development in biodegradable and biocompatible materials is briefly discussed.

Abstract Owing to its earth abundance, low kinetic overpotential, and superior stability, NiFe‐layered double hydroxide (NiFe‐LDH) has emerged as a promising electrocatalyst for catalyzing water splitting, especially oxygen evolution reaction (OER), in alkaline solutions. Unfortunately, as a result of extremely sluggish water dissociation kinetics (Volmer step), hydrogen evolution reaction (HER) activity of the NiFe‐LDH is rather poor in alkaline environment. Here a novel strategy is demonstrated for substantially accelerating the hydrogen evolution kinetics of the NiFe‐LDH by partially substituting Fe atoms with Ru. In a 1 m KOH solution, the as‐synthesized Ru‐doped NiFe‐LDH nanosheets (NiFeRu‐LDH) exhibit excellent HER performance with an overpotential of 29 mV at 10 mA cm −2 , which is much lower than those of noble metal Pt/C and reported electrocatalysts. Both experimental and theoretical results reveal that the introduction of Ru atoms into NiFe‐LDH can efficiently reduce energy barrier of the Volmer step, eventually accelerating its HER kinetics. Benefitting from its…

Abstract Inspired by nature, artificial photosynthesis through the construction of direct Z‐scheme photocatalysts is extensively studied for sustainable solar fuel production due to the effectiveness in enhancing photoconversion efficiency. However, there is still a lack of thorough understanding and direct evidence for the direct Z‐scheme charge transfer in these photocatalysts. Herein, a recyclable direct Z‐scheme composite film composed of titanium dioxide and cadmium sulfide (TiO2/CdS) is prepared for high‐efficiency photocatalytic carbon dioxide (CO2) reduction. In situ irradiated X‐ray photoelectron spectroscopy (ISI‐XPS) confirms the direct Z‐scheme charge‐carrier migration pathway in the photocatalytic system. Furthermore, density functional theory simulation identifies the intrinsic cause for the formation of the direct Z‐scheme heterojunction between the TiO2 and the CdS. Thanks to the significantly enhanced redox abilities of the charge carriers in the direct Z‐scheme system, the photocatalytic CO2 reduction performance of the optimized TiO2/CdS is 3.5, 5.4, and 6.3 times…

Abstract The electrochemical reduction of N 2 into NH 3 production under ambient conditions represents an attractive prospect for the fixation of N 2 . However, this process suffers from low yield rate of NH 3 over reported electrocatalysts. In this work, a record‐high activity for N 2 electrochemical reduction over Ru single atoms distributed on nitrogen‐doped carbon (Ru SAs/N‐C) is reported. At −0.2 V versus reversible hydrogen electrode, Ru SAs/N‐C achieves a Faradaic efficiency of 29.6% for NH 3 production with partial current density of −0.13 mA cm −2 . Notably, the yield rate of Ru SAs/N‐C reaches 120.9 , which is one order of magnitude higher than the highest value ever reported. This work not only develops a superior electrocatalyst for NH 3 production, but also provides a guideline for the rational design of highly active and robust single‐atom catalysts.

Abstract Metal–organic frameworks (MOFs) and MOF‐derived materials have recently attracted considerable interest as alternatives to noble‐metal electrocatalysts. Herein, the rational design and synthesis of a new class of Co@N‐C materials (C‐MOF‐C2‐T) from a pair of enantiotopic chiral 3D MOFs by pyrolysis at temperature T is reported. The newly developed C‐MOF‐C2‐900 with a unique 3D hierarchical rodlike structure, consisting of homogeneously distributed cobalt nanoparticles encapsulated by partially graphitized N‐doped carbon rings along the rod length, exhibits higher electrocatalytic activities for oxygen reduction and oxygen evolution reactions (ORR and OER) than that of commercial Pt/C and RuO2, respectively. Primary Zn–air batteries based on C‐MOF‐900 for the oxygen reduction reaction (ORR) operated at a discharge potential of 1.30 V with a specific capacity of 741 mA h gZn–1 under 10 mA cm–2. Rechargeable Zn–air batteries based on C‐MOF‐C2‐900 as an ORR and OER bifunctional catalyst exhibit initial charge and discharge potentials at 1.81 and 1.28 V (2 mA cm–2), along with an…

Abstract The discovery of stable and noble‐metal‐free catalysts toward efficient electrochemical reduction of nitrogen (N 2 ) to ammonia (NH 3 ) is highly desired and significantly critical for the earth nitrogen cycle. Here, based on the theoretical predictions, MoS 2 is first utilized to catalyze the N 2 reduction reaction (NRR) under room temperature and atmospheric pressure. Electrochemical tests reveal that such catalyst achieves a high Faradaic efficiency (1.17%) and NH 3 yield (8.08 × 10 −11 mol s −1 cm −1 ) at −0.5 V versus reversible hydrogen electrode in 0.1 m Na 2 SO 4 . Even in acidic conditions, where strong hydrogen evolution reaction occurs, MoS 2 is still active for the NRR. This work represents an important addition to the growing family of transition‐metal‐based catalysts with advanced performance in NRR.

Abstract The generation of green hydrogen (H 2 ) energy using sunlight is of great significance to solve the worldwide energy and environmental issues. Particularly, photocatalytic H 2 production is a highly promising strategy for solar‐to‐H 2 conversion. Recently, various heterostructured photocatalysts with high efficiency and good stability have been fabricated. Among them, 2D/2D van der Waals (VDW) heterojunctions have received tremendous attention, since this architecture can promote the interfacial charge separation and transfer and provide massive reactive centers. On the other hand, currently, most photocatalysts are composed of metal elements with high cost, limited reserves, and hazardous environmental impact. Hence, the development of metal‐free photocatalysts is desirable. Here, a novel 2D/2D VDW heterostructure of metal‐free phosphorene/graphitic carbon nitride (g‐C 3 N 4 ) is fabricated. The phosphorene/g‐C 3 N 4 nanocomposite shows an enhanced visible‐light photocatalytic H 2 production activity of 571 µmol h −1 g −1 in 18 v% lactic acid aqueous solution. This…

Recent advances in materials, manufacturing, biotechnology, and microelectromechanical systems (MEMS) have fostered many exciting biosensors and bioactuators that are based on biocompatible piezoelectric materials. These biodevices can be safely integrated with biological systems for applications such as sensing biological forces, stimulating tissue growth and healing, as well as diagnosing medical problems. Herein, the principles, applications, future opportunities, and challenges of piezoelectric biomaterials for medical uses are reviewed thoroughly. Modern piezoelectric biosensors/bioactuators are developed with new materials and advanced methods in microfabrication/encapsulation to avoid the toxicity of conventional lead-based piezoelectric materials. Intriguingly, some piezoelectric materials are biodegradable in nature, which eliminates the need for invasive implant extraction. Together, these advancements in the field of piezoelectric materials and microsystems can spark a new age in the field of medicine.

Photodynamic therapy is arising as a noninvasive treatment modality for cancer and other diseases. One of the key factors to determine the therapeutic function is the efficiency of photosensitizers (PSs). Opposed to traditional PSs, which show quenched fluorescence and reduced singlet oxygen production in the aggregate state, PSs with aggregation-induced emission (AIE) exhibit enhanced fluorescence and strong photosensitization ability in nanoparticles. Here, the design principles of AIE PSs and their biomedical applications are discussed in detail, starting with a summary of traditional PSs, followed by a comparison between traditional and AIE PSs to highlight the various design strategies and unique features of the latter. Subsequently, the applications of AIE PSs in photodynamic cancer cell ablation, bacteria killing, and image-guided therapy are discussed using charged AIE PSs, AIE PS molecular probes, and AIE PS nanoparticles as examples. These studies have demonstrated the great potential of AIE PSs as effective theranostic agents to treat tumor or bacterial infection. This…

Advances in biomaterials for drug delivery are enabling significant progress in biology and medicine. Multidisciplinary collaborations between physical scientists, engineers, biologists, and clinicians generate innovative strategies and materials to treat a range of diseases. Specifically, recent advances include major breakthroughs in materials for cancer immunotherapy, autoimmune diseases, and genome editing. Here, strategies for the design and implementation of biomaterials for drug delivery are reviewed. A brief history of the biomaterials field is first established, and then commentary on RNA delivery, responsive materials development, and immunomodulation are provided. Current challenges associated with these areas as well as opportunities to address long-standing problems in biology and medicine are discussed throughout.

2D layered materials (2DLMs) are a subject of intense research for a wide variety of applications (e.g., electronics, photonics, and optoelectronics) due to their unique physical properties. Most recently, increasing research efforts on 2DLMs are projected toward the nonlinear optical properties of 2DLMs, which are not only fascinating from the fundamental science point of view but also intriguing for various potential applications. Here, the current state of the art in the field of nonlinear optics based on 2DLMs and their hybrid structures (e.g., mixed-dimensional heterostructures, plasmonic structures, and silicon/fiber integrated structures) is reviewed. Several potential perspectives and possible future research directions of these promising nanomaterials for nonlinear optics are also presented.

Abstract It is highly desirable yet remains challenging to improve the dispersion and usage of noble metal cocatalysts, beneficial to charge transfer in photocatalysis. Herein, for the first time, single Pt atoms are successfully confined into a metal–organic framework (MOF), in which electrons transfer from the MOF photosensitizer to the Pt acceptor for hydrogen production by water splitting under visible‐light irradiation. Remarkably, the single Pt atoms exhibit a superb activity, giving a turnover frequency of 35 h −1 , ≈30 times that of Pt nanoparticles stabilized by the same MOF. Ultrafast transient absorption spectroscopy further unveils that the single Pt atoms confined into the MOF provide highly efficient electron transfer channels and density functional theory calculations indicate that the introduction of single Pt atoms into the MOF improves the hydrogen binding energy, thus greatly boosting the photocatalytic H 2 production activity.

Due to their well-defined 3D architectures, permanent porosity, and diverse chemical functionalities, metal-organic framework nanoparticles (MOF NPs) are an emerging class of modular nanomaterials. Herein, recent developments in the synthesis and postsynthetic surface functionalization of MOF NPs that strengthen the fundamental understanding of how such structures form and grow are highlighted; the internal structure and external surface properties of these novel nanomaterials are highlighted as well. These fundamental advances have resulted in MOF NPs being used as components in chemical sensors, biological probes, and membrane separation materials, as well as building blocks for colloidal crystal engineering.

The emergence and global spread of bacterial resistance to currently available antibiotics underscore the urgent need for new alternative antibacterial agents. Recent studies on the application of nanomaterials as antibacterial agents have demonstrated their great potential for management of infectious diseases. Among these antibacterial nanomaterials, carbon-based nanomaterials (CNMs) have attracted much attention due to their unique physicochemical properties and relatively higher biosafety. Here, a comprehensive review of the recent research progress on antibacterial CNMs is provided, starting with a brief description of the different kinds of CNMs with respect to their physicochemical characteristics. Then, a detailed introduction to the various mechanisms underlying antibacterial activity in these materials is given, including physical/mechanical damage, oxidative stress, photothermal/photocatalytic effect, lipid extraction, inhibition of bacterial metabolism, isolation by wrapping, and the synergistic effect when CNMs are used in combination with other antibacterial materials,…

The near-infrared window between 1000 and 1700 nm, commonly termed the "second near-infrared (NIR-II) window," has quickly emerged as a highly attractive optical region for biological imaging. In contrast to conventional imaging in the visible region between 400 and 700 nm, as well as in the first NIR (NIR-I) window between 700 and 900 nm, NIR-II biological imaging offers numerous merits, including higher spatial resolution, deeper penetration depth, and lower optical absorption and scattering from biological substrates with minimal tissue autofluorescence. Noninvasive imaging techniques, specifically NIR-II fluorescence and photoacoustic (PA) imaging, have embodied the attractiveness of NIR-II optical imaging, with several NIR-II contrast agents demonstrating superior performance to the clinically approved NIR-I agents. Consequently, NIR-II biological imaging has been increasingly explored due to its tremendous potential for preclinical studies and clinical utility. Herein, the progress of optical imaging in the NIR-II window is reported. Starting with highlighting the importance…

Proton-exchange-membrane fuel cells (PEMFCs) are of considerable interest for direct chemical-to-electrical energy conversion and may represent an ultimate solution for mobile power supply. However, PEMFCs today are primarily limited by the sluggish kinetics of the cathodic oxygen reduction reaction (ORR), which requires a significant amount of Pt-based catalyst with a substantial contribution to the overall cost. Hence, promoting the activity and stability of the needed catalyst and minimizing the amount of Pt loaded are central to reducing the cost of PEMFCs for commercial deployment. Considerable efforts have been devoted to improving the catalytic performance of Pt-based ORR catalysts, including the development of various Pt nanostructures with tunable sizes and chemical compositions, controlled shapes with selectively displayed crystallographic surfaces, tailored surface strains, surface doping, geometry engineering, and interface engineering. Herein, a brief introduction of some fundamentals of fuel cells and ORR catalysts with performance metrics is provided, followed by a…

Polymers are usually considered as thermal insulators, and their applications are limited by their low thermal conductivity. However, recent studies have shown that certain polymers have surprisingly high thermal conductivity, some of which are comparable to that in poor metals or even silicon. Here, the experimental achievements and theoretical progress of thermal transport in polymers and their nanocomposites are outlined. The open questions and challenges of existing theories are discussed. Special attention is given to the mechanism of thermal transport, the enhancement of thermal conductivity in polymer nanocomposites/fibers, and their potential application as thermal interface materials.

The trap states at grain boundaries (GBs) within polycrystalline perovskite films deteriorate their optoelectronic properties, making GB engineering particularly important for stable high-performance optoelectronic devices. It is demonstrated that trap states within bulk films can be effectively passivated by semiconducting molecules with Lewis acid or base functional groups. The perovskite crystallization kinetics are studied using in situ synchrotron-based grazing-incidence X-ray scattering to explore the film formation mechanism. A model of the passivation mechanism is proposed to understand how the molecules simultaneously passivate the Pb-I antisite defects and vacancies created by under-coordinated Pb atoms. In addition, it also explains how the energy offset between the semiconducting molecules and the perovskite influences trap states and intergrain carrier transport. The superior optoelectronic properties are attained by optimizing the molecular passivation treatments. These benefits are translated into significant enhancements of the power conversion efficiencies to 19.3%,…

Photocatalysis for solar-driven reactions promises a bright future in addressing energy and environmental challenges. The performance of photocatalysis is highly dependent on the design of photocatalysts, which can be rationally tailored to achieve efficient light harvesting, promoted charge separation and transport, and accelerated surface reactions. Due to its unique feature, semiconductors with hollow structure offer many advantages in photocatalyst design including improved light scattering and harvesting, reduced distance for charge migration and directed charge separation, and abundant surface reactive sites of the shells. Herein, the relationship between hollow nanostructures and their photocatalytic performance are discussed. The advantages of hollow nanostructures are summarized as: 1) enhancement in the light harvesting through light scattering and slow photon effects; 2) suppression of charge recombination by reducing charge transfer distance and directing separation of charge carriers; and 3) acceleration of the surface reactions by increasing accessible surface areas…

Water harvesting from air in passive, adsorption-based devices holds great potential for delivering drinking water to arid regions of the world. This technology requires adsorbents that can be tailored for a maximum working capacity, temperature response, and the relative pressure range in which reversible adsorption occurs. In this respect, metal-organic frameworks (MOFs) are promising, owing to their structural diversity and the precision of their functionalization for adjusting both pore size and hydrophilicity, thereby facilitating the rational design of their water-sorption characteristics. Here, chemical and structural factors crucial for the design of hydrolytically stable MOFs for water adsorption are discussed. Prevalent water adsorption mechanisms in micro- and mesoporous MOFs alongside strategies for fine-tuning of their adsorption behavior by means of reticular chemistry are presented. Finally, an approach for the selection of promising MOFs with respect to water harvesting from air is proposed and design concepts for next-generation MOFs for application in passive…

Abstract Halide perovskites, including CsPbX3 (X = Cl, Br, I), have gained much attention in the field of optoelectronics. However, the toxicity of Pb and the low photoluminescence quantum yield (PLQY) of these perovskites hamper their use. In this work, new halide materials that meet the requirements of: (i) nontoxicity, (ii) high PLQY, and (iii) ease of fabrication of thin films via the solution process are explored. In particular, copper(I) halide compounds with low‐dimensional electronic structures are considered. Cs3Cu2I5 has a 0D photoactive site and exhibits blue emission (≈445 nm) with very high PLQYs of ≈90 and ≈60% for single crystals and thin films, respectively. The large exciton binding energy of ≈490 meV explains well the 0D electronic nature of Cs3Cu2I5. Blue electroluminescence of Pb‐free halides is demonstrated using solution‐derived Cs3Cu2I5 thin films.

Liquid crystal elastomers (LCEs) are soft materials capable of large, reversible shape changes, which may find potential application as artificial muscles, soft robots, and dynamic functional architectures. Here, the design and additive manufacturing of LCE actuators (LCEAs) with spatially programed nematic order that exhibit large, reversible, and repeatable contraction with high specific work capacity are reported. First, a photopolymerizable, solvent-free, main-chain LCE ink is created via aza-Michael addition with the appropriate viscoelastic properties for 3D printing. Next, high operating temperature direct ink writing of LCE inks is used to align their mesogen domains along the direction of the print path. To demonstrate the power of this additive manufacturing approach, shape-morphing LCEA architectures are fabricated, which undergo reversible planar-to-3D and 3D-to-3D' transformations on demand, that can lift significantly more weight than other LCEAs reported to date.

Abstract Recently, a new class of 2D materials, i.e., transition metal carbides, nitrides, and carbonitrides known as MXenes, is unveiled with more than 20 types reported one after another. Since they are flexible and conductive, MXenes are expected to compete with graphene and other 2D materials in many applications. Here, a general route is reported to simple self‐assembly of transition metal oxide (TMO) nanostructures, including TiO2 nanorods and SnO2 nanowires, on MXene (Ti3C2) nanosheets through van der Waals interactions. The MXene nanosheets, acting as the underlying substrate, not only enable reversible electron and ion transport at the interface but also prevent the TMO nanostructures from aggregation during lithiation/delithiation. The TMO nanostructures, in turn, serve as the spacer to prevent the MXene nanosheets from restacking, thus preserving the active areas from being lost. More importantly, they can contribute extraordinary electrochemical properties, offering short lithium diffusion pathways and additional active sites. The resulting TiO2/MXene and SnO2/MXene…

Abstract Electrocatalytic nitrogen fixation is considered a promising approach to achieve NH 3 production. However, due to the chemical inertness of nitrogen, it is necessary to develop efficient catalysts to facilitate the process of nitrogen reduction. Here, molybdenum carbide nanodots embedded in ultrathin carbon nanosheets (Mo 2 C/C) are developed to serve as a catalyst candidate for highly efficient and robust N 2 fixation through an electrocatalytic nitrogen reduction reaction (NRR). The as‐synthesized Mo 2 C/C nanosheets show excellent catalytic performance with a high NH 3 yield rate (11.3 µg h −1 mg −1 Mo2C ) and Faradic efficiency (7.8%) for NRR under ambient conditions. More importantly, the isotopic experiments using 15 N 2 as a nitrogen source confirm that the synthesized ammonia is derived from the direct supply of nitrogen. This result also demonstrates the possibility of high‐efficiency nitrogen reduction even though accompanied with vigorous hydrogen evolution.

To make organic solar cells (OSCs) more competitive in the diverse photovoltaic cell technologies, it is very important to demonstrate that OSCs can achieve very good efficiencies and that their cost can be reduced. Here, a pair of nonfullerene small-molecule acceptors, IT-2Cl and IT-4Cl, is designed and synthesized by introducing easy-synthesis chlorine substituents onto the indacenodithieno[3,2-b]thiophene units. The unique feature of the large dipole moment of the CCl bond enhances the intermolecular charge-transfer effect between the donor-acceptor structures, and thus expands the absorption and down shifts the molecular energy levels. Meanwhile, the introduction of CCl also causes more pronounced molecular stacking, which also helps to expand the absorption spectrum. Both of the designed OSCs devices based on two acceptors can deliver a power conversion efficiency (PCE) greater than 13% when blended with a polymer donor with a low-lying highest occupied molecular orbital level. In addition, since IT-2Cl and IT-4Cl have very good compatibility, a ternary OSC device integrating…

Using memristor crossbar arrays to accelerate computations is a promising approach to efficiently implement algorithms in deep neural networks. Early demonstrations, however, are limited to simulations or small-scale problems primarily due to materials and device challenges that limit the size of the memristor crossbar arrays that can be reliably programmed to stable and analog values, which is the focus of the current work. High-precision analog tuning and control of memristor cells across a 128 × 64 array is demonstrated, and the resulting vector matrix multiplication (VMM) computing precision is evaluated. Single-layer neural network inference is performed in these arrays, and the performance compared to a digital approach is assessed. Memristor computing system used here reaches a VMM accuracy equivalent of 6 bits, and an 89.9% recognition accuracy is achieved for the 10k MNIST handwritten digit test set. Forecasts show that with integrated (on chip) and scaled memristors, a computational efficiency greater than 100 trillion operations per second per Watt is possible.

Ferroptosis, a new form of regulated cell death that is iron- and reactive oxygen species dependent, has attracted much attention in the research communities of biochemistry, oncology, and especially material sciences. Since the first demonstration in 2012, a series of strategies have been developed to induce ferroptosis of cancer cells, including the use of nanomaterials, clinical drugs, experimental compounds, and genes. A plethora of research work has outlined the blueprint of ferroptosis as a new option for cancer therapy. However, the published ferroptosis-related reviews have mainly focused on the mechanisms and pathways of ferroptosis, which motivated this contribution to bridge the gap between biological significance and material design. Therefore, it is timely to summarize the previous efforts on the emerging strategies for inducing ferroptosis and shed light on future directions for using such a tool to fight against cancer. Here, the current strategies of cancer therapy based on ferroptosis will be elaborated, the design considerations and the advantages and limitations…

Abstract The oxygen reduction reaction (ORR) is a core reaction for electrochemical energy technologies such as fuel cells and metal–air batteries. ORR catalysts have been limited to platinum, which meets the requirements of high activity and durability. Over the last few decades, a variety of materials have been tested as non‐Pt catalysts, from metal–organic complex molecules to metal‐free catalysts. In particular, nitrogen‐doped graphitic carbon materials, including N‐doped graphene and N‐doped carbon nanotubes, have been extensively studied. However, due to the lack of understanding of the reaction mechanism and conflicting knowledge of the catalytic active sites, carbon‐based catalysts are still under the development stage of achieving a performance similar to Pt‐based catalysts. In addition to the catalytic viewpoint, designing mass transport pathways is required for O2. Recently, the importance of pyridinic N for the creation of active sites for ORR and the requirement of hydrophobicity near the active sites have been reported. Based on the increased knowledge in controlling…

As the key of hydrogen economy, electrocatalytic hydrogen evolution reactions (HERs) depend on the availability of cost-efficient electrocatalysts. Over the past years, there is a rapid rise in noble-metal-free electrocatalysts. Among them, transition metal carbides (TMCs) are highlighted due to their structural and electronic merits, e.g., high conductivity, metallic band states, tunable surface/bulk architectures, etc. Herein, representative efforts and progress made on TMCs are comprehensively reviewed, focusing on the noble-metal-like electronic configuration and the relevant structural/electronic modulation. Briefly, specific nanostructures and carbon-based hybrids are introduced to increase active-site abundance and to promote mass transportation, and heteroatom doping and heterointerface engineering are encouraged to optimize the chemical configurations of active sites toward intrinsically boosted HER kinetics. Finally, a perspective on the future development of TMC electrocatalysts is offered. The overall aim is to shed some light on the exploration of emerging materials in…

Organic-inorganic hybrid perovskite materials are receiving increasing attention and becoming star materials on account of their unique and intriguing optical and electrical properties, such as high molar extinction coefficient, wide absorption spectrum, low excitonic binding energy, ambipolar carrier transport property, long carrier diffusion length, and high defects tolerance. Although a high power conversion efficiency (PCE) of up to 22.7% is certified for perovskite solar cells (PSCs), it is still far from the theoretical Shockley-Queisser limit efficiency (30.5%). Obviously, trap-assisted nonradiative (also called Shockley-Read-Hall, SRH) recombination in perovskite films and interface recombination should be mainly responsible for the above efficiency distance. Here, recent research advancements in suppressing bulk SRH recombination and interface recombination are systematically investigated. For reducing SRH recombination in the films, engineering perovskite composition, additives, dimensionality, grain orientation, nonstoichiometric approach, precursor solution, and…